RECD Ash Collection Containers: Labelling and Temporary Storage Planning

The first time an RECD filter is cleaned on your site, someone will ask a simple question: where does the ash go?

If nobody has planned an answer, it goes into whatever is nearby. An empty paint tin, a cement bag, a bucket with no lid. Then it sits in a corner of the generator room, where a draught lifts the fine powder, a spilled bucket gets swept into the drain and an inspector finds an unlabelled container with unknown contents.

The quantities are small, which is exactly why the planning is skipped. But small and irregular is still a waste stream, and the rules for hazardous waste do not have a minimum bucket size. This guide helps you plan the temporary collection point for RECD ash and cleaning residues: how to choose containers, what a label must say, how long material may wait, what to record, what to keep nearby for a spill and how to size the whole arrangement. A worked weekly example shows how few kilograms are really involved, and a checklist closes the guide.

One caution. We are not lawyers, and your State Pollution Control Board authorisation, your waste category and the current rules govern what you must do. We describe common practice and the main points of the framework, and you should confirm details with your board or an authorised waste handler.

Why a planned corner beats an improvised one

Three reasons.

  1. Health. Fine ash and soot can be inhaled, and soot carries combustion by-products. Open handling in a draughty room spreads it. Our article on handling soot and ash removed during RECD servicing covers the handling side. This one covers where it waits.
  2. Compliance. In India, hazardous waste is regulated under the Hazardous and Other Wastes (Management and Transboundary Movement) Rules, 2016, and storage, labelling and records are part of the framework. State boards publish the forms, and Tamil Nadu’s board, for example, provides the Form VIII template used for container labelling (TNPCB Form VIII). Overseas, the California Air Resources Board states that DPF ash is treated as California hazardous waste unless tested and shown otherwise, which shows how seriously regulators treat it.
  3. Traceability. The ash came from a specific filter on a specific date. A container with a label and a register line lets you prove where it came from and where it went. See RECD certificates vs emissions test reports for how this fits into your wider evidence file.

First question: is it hazardous waste on your site?

Do not assume the answer either way. Whether RECD ash falls under a hazardous waste category depends on its composition (ash from lubricant additives, metals from fuel and wear, sorbents, soot) and on how your SPCB classifies it. Cleaning wipes, rags and gloves soaked in solvent or carrying ash are usually handled with it.

Practical steps:

  • Ask your SPCB or authorised waste handler which category and code apply to this stream.
  • If you have a Hazardous Waste authorisation, check whether this waste is covered, and add it if it is not.
  • If a third-party cleaning provider takes the element away and handles the waste at its own site, find out who the “occupier” is for that waste and who holds the authorisation. Our guide to packaging an ash-loaded filter for off-site cleaning covers the shipping side, and the same question arises there.
  • Keep the answer in writing.

Until you know, treat it as hazardous: contained, labelled and recorded. It costs little and avoids the awkward position of having to defend an improvised arrangement.

Designing the corner

The collection point is a small physical space. Think about six features.

FeatureGood practiceWhy
LocationAway from the engine and exhaust, from drains, from walkways and from air intakesHot surfaces, spills and draughts are the main risks
FloorImpermeable, with a low bund or tray beneath containersContains a spill
CoverUnder a roof, out of rainRain turns ash to slurry and corrodes drums
AccessReachable by the person who handles waste and by the collector’s vehicleAvoids carrying across the plant
SeparationApart from fuel, oil, food and general wasteAvoids contamination and cross-reaction
SignageA visible hazardous waste sign and instructionsInforms everyone entering

Size the footprint to the containers. A single drum with a tray may need less than a square metre. For a multi-site programme, see RECD asset register for a multi-site DG fleet to organise the information.

Choosing containers

The material is a fine, dry powder or a damp sludge, depending on how it was removed. It can also carry oil. Choose for containment first.

ContainerGood forCautions
Heavy-duty polyethylene drum with a tight lid (20–60 L)Dry ash and soot, sealed bags of residueCheck compatibility with any solvent present
Steel drum with a clamp-ring lidOily residues, ragsCorrosion if wet; check linings
Heavy-gauge plastic bags, double-bagged, inside a rigid containerWipes, gloves, small quantitiesBags alone are not storage; they go inside a rigid, lidded container
Open buckets, cement bags, loose sacksNothingNot suitable

Rules of thumb:

  • Always a lid, kept closed except when adding waste.
  • One stream per container. Do not mix ash with oily rags, sorbent or general rubbish.
  • Leave headspace. Do not fill beyond about three-quarters, so that the lid seals and handling does not spill.
  • Use a container sized to the load. A 200 L drum for 3 kg of ash tempts people to add other things.
  • Choose a container you can move safely. A full drum of fine ash is heavy for its volume. Do not exceed what the handler can lift.
  • Keep it upright and stable on the tray.

Labelling: what the label must carry

Labelling is where most improvised arrangements fail. A hazardous waste container label follows the format in the Rules, and state board forms reproduce the layout. The elements usually include:

Label elementNotes
The words “HAZARDOUS WASTE”Clearly visible, in English and the local language
Waste category and descriptionFor example, the category your SPCB assigned and a plain description such as “RECD filter ash and soot”
Name and address of the occupier (generator)Your site
Contact detailsA named phone number
Date of storage / date waste first put in the containerStarts the clock
QuantityWeight or volume, updated or finalised when closed
Nature of hazardPictogram or statement, for example toxic, harmful
Handling precautionsShort note, such as “avoid dust; wear mask and gloves”
Authorisation or registration numberWhere applicable

The labels should be weatherproof and not easily washed off or detached, and the lettering should be large enough to read at a distance. Take the exact wording and layout from your State board’s current form rather than from this article, because layouts and fields are updated.

A template you can adapt

Use this as a worksheet, not as a legal label.

FieldExample entry (illustrative)
WasteRECD filter ash and soot (dry)
Category / codeAs assigned by SPCB: [enter]
Generator[Site name and address]
Contact[Name, phone]
First added[dd/mm/yyyy]
Closed[dd/mm/yyyy]
Net quantity[kg]
SourceElement ID [x], cleaned [date], job ref [n]
HazardHarmful dust; avoid inhalation
PrecautionsMask and gloves; keep lid closed; do not wash into drain

Adding the source line is our suggestion, not a label rule. It links the container to your cleaning records, which helps if you are asked where the ash came from.

One label, one container, one story

Put a new label on a new container before the first scoop goes in. Never re-use a container with an old label showing, and never write on masking tape that peels. If you reuse a drum, remove the old label completely.

How long may it wait?

Storage time limits exist for hazardous waste. Under the 2016 Rules, the general limit for storage on the occupier’s site is commonly cited as 90 days, with the State Pollution Control Board able to allow longer in some circumstances. Treat that as the figure to confirm with your board, because authorisation conditions can differ.

Planning implications:

  • The clock starts at the date on the label, so write the date when the first waste goes in, not when the drum is closed.
  • Do not let a drum sit half-full for months. Either close it and date it, or arrange pick-up before the limit.
  • Book the collector in advance and align the collection with your cleaning calendar. Our article on RECD cleaning intervals helps you predict when waste will arise.
  • Use an authorised collector or recycler and keep the manifest. Movement of hazardous waste between sites is also governed by the Rules, including a manifest system, so ask the handler to explain what they will provide.

The storage register

A one-page register turns the corner into a record. A simple ledger, kept in a folder at the corner or in a shared sheet:

DateContainer IDAction (add / close / collect)Source (element ID, job)Net kgInitialsCollector and manifest ref
04-11D1AddElement 3, job 1180.8RK
04-11D1Add (wipes)Element 3, job 1180.3RK
18-11D1CloseTotal 1.1RK
05-12D1Collect1.1RKCollector X, manifest 4471

The register answers four questions at a glance: what is here, how long has it been here, where did it come from and where did it go. It pairs naturally with the RECD event log and the shift handover log, since both can note that waste was generated.

A worked example: how much waste are we really talking about?

The numbers are illustrative. A site has 12 DG sets with RECDs. Each element is cleaned twice a year. Per cleaning, assume:

  • 0.8 kg of dry ash and soot recovered
  • 0.3 kg of wipes and rags
  • 0.5 kg of gloves, disposable coveralls, sheeting and filter masks

Annual quantities

  • Ash and soot: 12 × 2 × 0.8 = 19.2 kg
  • Wipes: 12 × 2 × 0.3 = 7.2 kg
  • PPE and sheeting: 12 × 2 × 0.5 = 12.0 kg
  • Total: 19.2 + 7.2 + 12.0 = 38.4 kg a year

Average per week: 38.4 ÷ 52 ≈ 0.74 kg. It looks trivial. But the waste does not arise evenly. Suppose the 24 cleanings are grouped into four campaigns of six, one per quarter.

  • Waste per campaign: 6 × (0.8 + 0.3 + 0.5) = 6 × 1.6 = 9.6 kg

Container sizing

  • Assume the mixed contaminated solids pack at about 0.3 kg per litre when bagged (assumed). Per campaign: 9.6 ÷ 0.3 = 32 litres.
  • At three-quarters fill, the container needs about 32 ÷ 0.75 ≈ 43 litres. A 60 L drum per stream is comfortable, or two 30 L drums if you segregate dry ash from contaminated rags.

Storage time

  • A campaign every quarter means roughly 90 days between campaigns. If you wait until the drum is “full”, it may not be full until the next campaign, and the label date can drift past the permitted period. The fix is to collect after each campaign, or to close and date a new drum for each one.

Reading it. The annual quantity is small enough for one or two drums, and the real planning issue is not volume but time and labelling. The risk is a part-filled, undated drum that sits in a corner for a year.

If the cleaning is done off site by a provider, most of this waste arises at the provider’s premises, and your own corner may only see rags and packaging from removing the element. Ask who classifies, stores and manifests the waste, and have the answer in the contract. See what an RECD cleaning quote should include.

Training the people who touch it

A well-built corner still fails if the person adding waste has never been shown how. A ten-minute briefing for each technician and contractor covers the essentials.

  1. What goes in and what does not. Ash, soot, contaminated wipes and used PPE go in. Fuel, oil, solvents, food waste and general rubbish do not.
  2. How to add waste. Open the lid, add the sealed bag, close the lid. Do not tip loose powder from a height.
  3. How to fill in the label and register. Date, source, quantity, initials.
  4. What to do in a spill. Stop, isolate, put on PPE, damp-clean, bag, label, record.
  5. Whom to call. The named custodian, with a phone number on the sign.

Record the briefing with names and dates. Contractors who arrive for a single cleaning job should receive the same briefing before they start, because they are the people most likely to leave a bag on the floor and walk away.

Monsoon, heat and dust

Indian site conditions put extra strain on a temporary store.

  • Monsoon. Raise containers off the floor on a tray or pallet, keep the area roofed and check that rainwater cannot run in from the sides. A wet drum rusts, a wet label peels and wet ash becomes sludge that is harder to handle.
  • Heat. Do not park drums in direct sun or next to hot exhaust pipes. Heat softens plastic, weakens lid seals and raises the fire risk when oily rags are present.
  • Dust. Where the corner is near a doorway or a vent, add a simple screen so that a draught cannot lift powder when a lid is open.
  • Pests. Keep food and drink away from the corner, and keep lids closed.

The spill kit

A spill of fine ash is not dramatic, but it is easily made worse by a broom. Keep a small kit at the corner:

  • Dust mask or respirator suited to fine particulate, and gloves and eye protection
  • A damp-wipe approach: lightly dampened disposable wipes or a vacuum cleaner with a suitable filter, instead of dry sweeping
  • Spare heavy-duty bags and a spare labelled container
  • Tape and a marker for relabelling
  • A short instruction card: stop, isolate, wear PPE, damp-clean, bag, label, record
  • Absorbent pads if oily residues are present

Rules: never hose ash into a drain, never burn it on site and never mix it into general rubbish. Used spill materials go into the same waste stream.

Pre-collection and handover

When the collector arrives:

  1. Check the collector’s authorisation and vehicle documents against what you were told.
  2. Close and label the container, and confirm the label is intact.
  3. Weigh or estimate the net quantity and enter it in the register.
  4. Complete the manifest, and keep your copy.
  5. Photograph the labelled container before it is loaded.
  6. Update the register with the collector and the reference.

Keep the manifest, the register and the photographs together with the cleaning certificate for the same element. If you are ever asked about the ash from element 3 on 4 November, you can answer with paperwork. For a picture of what the inspector may ask, see what happens during a pollution control board inspection and the environmental compliance checklist for generator owners.

Who does what

TaskOwner
Confirm waste category and authorisationEHS / compliance
Provide containers, labels, tray and spill kitEHS or facility
Fill the container and complete the labelTechnician doing the cleaning or removal
Keep the registerWaste custodian (named person)
Weekly check of cornerEHS or supervisor
Arrange collection and manifestEHS with authorised collector
Keep recordsCompliance

A named custodian matters. Without one, the corner belongs to nobody.

A weekly walk-round checklist

  • Lids on and closed
  • Labels present, legible, dated
  • Containers upright and on the tray
  • No spillage, dust or staining around the corner
  • Spill kit complete
  • Register up to date, with dates inside the permitted period
  • Signage in place
  • Nothing else stored in the corner
  • Collection booked for any container nearing its limit

Mistakes to avoid

  • Using open buckets, sacks or tins.
  • Mixing streams (ash, oily rags, general waste).
  • Writing no date on the label.
  • Letting a drum age. The storage limit applies to time, not to fullness.
  • Dry sweeping spills and raising dust.
  • Washing residue to a drain.
  • Not knowing who holds the authorisation when a provider takes the waste.
  • Relying on memory instead of a register.

Frequently asked questions

Is RECD ash hazardous waste in India?

It depends on its composition and on how your State Pollution Control Board classifies it. Ask your board or authorised handler, and in the meantime store it as hazardous waste: contained, labelled and recorded.

What must be on a hazardous waste container label?

Typically the words “HAZARDOUS WASTE”, waste category and description, the generator’s name and address, contact details, date of storage, quantity and hazard and handling information, in English and the local language. Use the layout in your board’s current form.

How long can we keep the waste on site?

The 2016 Rules are commonly cited as allowing 90 days, with possible extension by the board. Confirm the period in your authorisation.

Can the cleaning provider take the ash away?

Yes in many arrangements, but check who is responsible for it, who holds the authorisation and what paperwork you will receive. Put it in the contract.

What size drum do we need?

Size to the quantity per campaign. In our illustrative example a site with twelve sets generated about 9.6 kg per campaign, which fits a 60 L drum with room to spare. Count your own numbers.

Can we put it in ordinary rubbish?

No. Do not mix RECD ash or contaminated materials with general waste, and do not put it in a drain.

Closing thought

The ash from an RECD is small in quantity and large in consequence if it is mishandled. Decide whether it is hazardous waste on your site, choose a lidded container, label it with the date of the first addition, keep a one-page register and book collection within the permitted time. Name a custodian, keep a spill kit and do a weekly walk-round. The result is a corner that takes up a square metre and stands up to an inspector’s question.

If you would like help planning an RECD servicing programme that includes waste handling, browse our retrofit emission control devices, see our DG set emission regulations guide or contact the Aceget team.

Keep reading



Leave a Reply