- November 18, 2026
- Posted by: editor
- Category: RECD & Emission Control Devices
An inspector from the pollution control board asks to see the paperwork for your RECD. Your facility manager hands over a neat certificate from the cleaning contractor: element weighed, flow tested, “cleaned to specification”. The inspector reads it, nods politely and asks, “And the emission test report?”
The two documents look similar. Both have a letterhead, a date, some numbers and a signature. Both use the word “certificate” or “report”. Yet they answer completely different questions, and handing one over in place of the other is a common and avoidable mistake.
This article sets the RECD cleaning certificate and the emissions test report side by side. We explain what each document is, what it measures, what it can and cannot prove and who relies on it. A worked example then shows why an excellent cleaning result can coexist with a device that no longer captures particulate, which is the clearest way to see why the documents are not interchangeable. We finish with a stakeholder-to-document matrix, a timeline showing where each document belongs in the life of a device, wording to ask for and avoid and an evidence-file index you can adopt.
A note on scope. We are not lawyers, and the exact documents an authority wants depend on your State Pollution Control Board, your consent conditions and the date of any order that applies to you. Treat this as a way of understanding the documents, and confirm requirements with your board or a qualified adviser.
Two documents, two questions
Everything else in this article follows from this table.
| Cleaning certificate (or service report) | Emissions test report | |
|---|---|---|
| The question it answers | “Was this filter element cleaned, and is its flow restored?” | “Does this device, on this engine, capture the particulate it claims to?” |
| What is under test | A single element, on a bench | The RECD installed on an engine, running a defined cycle |
| What is measured | Weight, pressure drop or airflow, visual condition | Particulate matter (and sometimes other pollutants) upstream and downstream of the device |
| Where it happens | Workshop or on site, with a flow bench or similar | An accredited or recognised test laboratory, or a witnessed site test |
| Instrument | Scale and flow bench | Gas and particulate sampling equipment, to a defined method |
| Reference | The element’s clean baseline | A test standard and a pass criterion |
| Who issues it | The cleaning provider | A test laboratory or test body |
| When it is issued | After each cleaning | At type approval, commissioning, and after significant changes |
| What it can prove | Cleaning was done, deposit was removed, flow was restored | Particulate capture efficiency, under test conditions |
| What it cannot prove | That the element still filters; that the device meets any emission limit | That the filter is clean today; that it will perform the same after years of service |
| Typical reader | Maintenance, supplier, warranty assessor | Regulator, auditor, customer, ESG reviewer |
The cleaning certificate is a maintenance record. The emissions test report is a performance record. They belong to different parts of the same story.
What the regulatory framework asks for
Understanding the rules shows why the emissions side carries weight. The Central Pollution Control Board (CPCB) issued a circular titled “System and Procedure for Emission Compliance Testing of Retro-fit Emission Control Devices (RECD)” for diesel generator set engines up to 800 kW gross mechanical power, following a National Green Tribunal order. That is summarised in a state board’s reply before the Tribunal (NGT filing, Chhattisgarh Environment Conservation Board). The same filing records the state’s direction that DG sets of 125 kVA and above be retrofitted with a device that has a minimum particulate-matter capturing efficiency of at least 70%, tested as per the ISO 8178 D2 five-mode cycle, and that establishments maintain records of installation, testing certificates and operation and maintenance, to be produced when required.
A CPCB report to the Tribunal frames the compliance route as retrofitted emission control equipment with at least 70% PM capture, type approved by one of the CPCB-recognised laboratories, as an alternative to gas-based generators (CPCB report to NGT). A commentary on a Karnataka circular advises buyers to check the certification and test report instead of relying on the vendor’s claim (Corpseed).
Three points follow for our purposes.
- The regulatory yardstick is particulate capture, tested under a defined procedure. That is the emissions test report’s territory.
- The records an authority may ask for are broader than the test report. Installation records, testing certificates and operation and maintenance records are all mentioned. Your cleaning certificates belong to the last group.
- Your State Pollution Control Board sets the details. What a particular board asks to see on an inspection day can differ. Our articles on what happens during a pollution control board inspection and the environmental compliance checklist for generator owners give the general picture.
For how to read the type-approval paperwork itself, see how to read an RECD test certificate and how to verify a CPCB-tested RECD.
The cleaning certificate in detail
What it is. A document from the cleaning provider describing what was done to an element and what was measured. It may be called a cleaning certificate, a service report, a flow test sheet or a data sheet.
What a good one contains. Element identification, dates, intake inspection, before and after weight, before and after flow or pressure drop under stated conditions, the reference and the acceptance limit, the method used, waste handling, photographs and a verdict. We list the fifteen items in how to verify that an RECD cleaning service was effective.
Why it matters. A trade article quoting a truck-parts manufacturer argued that testing after cleaning is the most critical part of the process, because it is the only way to know whether a filter is clean enough to reinstall (FleetOwner). A service company’s guidance advises insisting on a dated data sheet that summarises the before and after condition of the filter (Fleet Maintenance). Those documents serve maintenance and warranty. See what to record for an RECD warranty claim.
What it cannot do. It does not measure what leaves the stack. It measures airflow resistance through the element and its mass. Neither of those is emission.
The emissions test report in detail
What it is. A report from a test laboratory or a witnessed test describing the measured emissions of the engine with and without the device, or upstream and downstream of it, under a defined test cycle and method.
What a good one contains. The device and engine identification, test conditions (load points, fuel, ambient), method and standard, instruments and calibration, sampling locations, results at each load point, the calculation of efficiency, uncertainty and a pass or fail against the criterion. Several of our articles help you read these: smoke opacity versus particulate mass, RECD emissions in mg/Nm³ versus g/kWh, why dilution misleads before and after measurements, comparing test results from different laboratories and interpreting uncertainty in an emission reduction claim.
Why it matters. It is the document that answers the regulator’s question. It also gives the only direct evidence of capture efficiency.
What it cannot do. It describes the device at the time of the test. It says nothing about the state of the filter two years later, and a test on one engine does not automatically carry over to a different engine or duty. Our articles on RECD efficiency, new versus aged and when to retest an RECD after DG set changes explain when a fresh test is worth having.
A worked example: great flow, poor capture
Here is why the documents cannot stand in for each other. The numbers are illustrative.
Two filter elements, A and B, are cleaned in the same workshop. Both pass the cleaning provider’s acceptance criterion, which requires a pressure drop at the test flow of no more than 46 mbar (the reference is 40 mbar and the limit is 15% above it).
| Element A (intact) | Element B (cracked) | |
|---|---|---|
| Pressure drop at test flow, after cleaning | 44 mbar | 30 mbar |
| Cleaning certificate verdict | Pass | Pass |
| Weight after cleaning versus dry reference | At reference | 0.2 kg below reference |
Both certificates say “pass”, and B’s flow looks even better than A’s. Now both elements are tested on an engine with the same upstream particulate concentration of 120 mg/Nm³.
| Element A | Element B | |
|---|---|---|
| Downstream particulate | 21.6 mg/Nm³ | 78 mg/Nm³ |
| Capture efficiency, (120 − downstream) ÷ 120 | (120 − 21.6) ÷ 120 = 82% | (120 − 78) ÷ 120 = 35% |
| Against a 70% criterion | Pass | Fail |
Reading it. A cracked or bypassed element resists flow less, because gas finds an easy path around the wall. A bench flow test can score that as a good result, while an emission test shows that the filter is barely filtering. The cleaning certificate answered its own question correctly (is flow restored?) and could not answer the regulator’s question (is particulate captured?). This is why a cleaning certificate must never be presented as proof of emission compliance, and why a damaged element can slip through cleaning documentation. See how to identify cleaning damage on an RECD filter for the physical clues that the flow test cannot see.
The converse holds as well. A good emissions test report from commissioning tells you nothing about whether the element is clean now. A filter that tested at 85% capture in year one may be heavily loaded with ash in year four.
Which stakeholder wants which document
Different people ask different questions, and the right document answers each.
| Stakeholder | Typical question | Document that answers it | Supporting documents |
|---|---|---|---|
| Pollution control board inspector | “Is the device type approved, and is it performing?” | Type approval certificate and emissions test report | Installation record, O&M and cleaning records |
| Enforcement during air-quality restrictions | “Is this DG set compliant with the conditions for operating?” | Device certification as the rule requires | Registration, consent documents; see GRAP rules for DG sets in Delhi-NCR |
| Supplier or manufacturer (warranty) | “Was the device maintained by an approved method?” | Cleaning certificate and service records | Event log, pressure history |
| Insurer | “Was the equipment maintained?” | Service records and cleaning certificates | Asset register |
| Internal auditor | “Is the maintenance plan being followed?” | Cleaning certificates against the interval plan | Ledger, cleaning interval card |
| Customer or tenant | “Is the DG set clean?” | Emissions test report summary | Compliance statement |
| ESG or sustainability reviewer | “What reduction can we claim?” | Emissions test report with uncertainty | Run hours, calculation; see RECD ESG disclosure metrics |
| Incoming owner or buyer | “What condition is this device in?” | Both, plus history | See due diligence for buying a building with an existing RECD |
Use the table the other way round, too. If someone asks for a document that does not answer their question, you will know to ask what they are really after.
Where each document belongs in the device’s life
| Stage | Event | Document produced |
|---|---|---|
| 1 | Type approval of the device model | Type approval certificate and laboratory test report |
| 2 | Purchase and delivery | Delivery inspection record; see RECD delivery inspection checklist |
| 3 | Installation and commissioning | Commissioning report, baseline pressure at the reference load, any on-site emissions test; see RECD trial installation acceptance criteria |
| 4 | Routine operation | Event log, pressure trend, regeneration records |
| 5 | Each cleaning | Cleaning certificate or report with before and after flow and weight |
| 6 | After significant change (engine overhaul, fuel change, duty change, device modification) | Retest or witnessed demonstration; see witnessed RECD performance demonstration |
| 7 | End of life or sale | Decommissioning record and history file; see planning RECD decommissioning and removal |
The cleaning certificates accumulate at stage 5, and the emissions evidence sits at stages 1, 3 and 6. Between the two, the pressure trend at the reference load, described in comparing RECD pressure readings at different generator loads, links the clean state to the tested state.
Wording to ask for and wording to avoid
Providers sometimes use wording that suggests more than a cleaning certificate delivers. Ask for precise wording and decline imprecise claims.
| Ask for | Be wary of |
|---|---|
| “Element ID [x] was cleaned by [method]. Pressure drop at [flow] before: [value]; after: [value]. Reference: [value]. Acceptance limit: [value]. Result: within limit.” | “Certified clean” |
| “Flow restored to within [x]% of reference.” | “Emission compliant after cleaning” |
| “No visible cracks, melting or plug loss on either face at final inspection, photographs ref. [n].” | “Filter in perfect condition” |
| “This certificate relates to element cleaning and does not constitute an emissions test.” | “Meets CPCB norms” on a cleaning document |
| “Mass removed [g]; waste handled by [named party], record [ref].” | “Waste disposed of properly” |
A good provider will not object to a disclaimer that says what the document is not. A document that tries to be both a cleaning record and a compliance certificate is a risk for you, because someone might rely on it for the wrong purpose.
What to say at an inspection
Prepare short, honest answers to the likely questions. An illustrative set:
- “Show me the device’s approval and test report.” You present the type approval certificate and the emissions test report. Our guide to verifying a CPCB-tested RECD covers what to check on them.
- “How is the device maintained?” You present the maintenance plan, the cleaning certificates, the pressure trend and the event log.
- “Is the filter performing today?” You present the latest pressure reading at the reference load against baseline, and the latest cleaning certificate. You say plainly that these show flow and maintenance, and that capture performance is shown by the emissions test report.
- “What changed since the test?” You present your change log: engine work, fuel, duty. If something material has changed, you note whether a retest is planned.
- “What happens to the ash?” You present waste records. See RECD ash collection containers: labelling and temporary storage.
Being clear about what each document proves tends to build credibility. Overstating tends to lose it.
An evidence-file index
Keep one folder per device. A suggested structure, with the document type, the question it answers and its owner.
| # | Folder | Contents | Question answered | Owner |
|---|---|---|---|---|
| 1 | Approval | Type approval certificate, laboratory report | Is the model approved? | Compliance |
| 2 | Purchase | Order, technical offer, deviations | What was bought? | Procurement |
| 3 | Installation | Drawings, GA, commissioning record, baseline | How was it installed and what was the starting state? | Projects |
| 4 | Testing | On-site emission tests, witnessed demonstrations, calibration records | Does it capture particulate? | Compliance |
| 5 | Operation | Event log, pressure trend, regeneration records, alarms | How is it behaving? | Operations |
| 6 | Cleaning | Cleaning certificates, packing and custody sheets, photographs, ledger | Was it maintained? | Maintenance |
| 7 | Waste | Containers, labels, manifests, receipts | Where did the ash go? | EHS |
| 8 | Changes | Engine work, fuel changes, modifications, retest decisions | What changed since testing? | Maintenance |
| 9 | Warranty and service | Warranty terms, claims, service reports | Who is responsible for what? | Procurement |
Our guide to the RECD asset register for a multi-site DG fleet shows how to scale this across several sets.
A quick test for any document you are handed
When a supplier, contractor or laboratory gives you a page with “certificate” or “report” in the title, run three checks before filing it.
- What object was examined? A single element on a bench points to a cleaning record. A whole device on a running engine points to an emissions test.
- What quantity was measured? Weight, airflow or pressure drop belong to maintenance. Particulate concentration, with an upstream and downstream sample, belongs to performance.
- Against what was it compared? A cleaning record compares with the element’s own baseline. An emissions report compares with a stated test method and a pass criterion.
If the answers do not line up with the title, ask the issuer to restate what the document covers. This takes two minutes and prevents the wrong paper from being shown to the wrong person months later.
Common mistakes
- Presenting a cleaning certificate as a compliance certificate.
- Presenting a commissioning test report as proof the filter is clean today.
- Accepting a cleaning certificate with no numbers.
- Assuming a good flow result means good capture, as the worked example showed.
- Keeping documents in different places, so that nobody can produce the whole story on inspection day.
- Forgetting to retest after significant changes to the engine, fuel or duty.
- Using a provider’s marketing language in your own compliance statements.
- Throwing away cleaning records after the warranty period.
Frequently asked questions
Does a DPF or RECD cleaning certificate prove compliance?
No. It shows that an element was cleaned and what flow and weight were measured. Compliance with particulate capture criteria is shown by a type approval and emissions test report under the applicable procedure. Confirm the specific requirement with your State Pollution Control Board.
Is a flow test report the same as an emissions test report?
No. A flow test measures resistance to airflow through an element on a bench. An emissions test measures particulate in the exhaust upstream and downstream of the device while the engine runs a defined cycle.
Which document should I show an inspector?
Both, for different questions. Show the type approval and test report for performance and the maintenance records, including cleaning certificates, for upkeep. Ask your board what it expects to see.
How long should I keep cleaning certificates?
For the life of the device, at least. They are the history that supports warranty, resale and lifecycle decisions. Check your board’s record-keeping conditions and any statutory retention rule.
Can a cleaning provider issue an emissions test report?
Only if it is a qualified test body working to the required method. A cleaning workshop issuing a flow test sheet is not doing an emissions test, whatever the document is called.
Do I need a new emissions test after every cleaning?
Not routinely. A retest is worth considering after significant changes such as an engine overhaul, a change of fuel or duty, a modification to the device or when evidence suggests damage. See when to retest an RECD after DG set changes.
Closing thought
Keep the cleaning certificate and the emissions test report, and keep them apart in your mind. One tells you that an element was maintained and that flow was restored. The other tells you what the device captures under test. A flow result can be excellent while capture is poor, so neither document can stand in for the other. Ask providers for precise wording, align each document with the stakeholder who needs it and keep a single evidence file for the life of the device.
If you would like help building an RECD evidence file or understanding what a document proves, browse our retrofit emission control devices, see our certifications or contact the Aceget team.
[…] cost of wrongly accepting. A damaged element is cleaned, passes a flow test (see our comparison in RECD cleaning certificates vs emissions test reports), and goes back on the engine. It then passes particulate straight through the crack. The owner […]