Rattling Inside an RECD: Loose Hardware or Substrate Damage?

Few sounds worry a maintenance team more than a rattle from a part that cost a lot of money and cannot be seen into. A retrofit emission control device (RECD) is a sealed, insulated canister. If something inside it is loose, nothing short of opening it will show you. So the sound has to do the work, and the question that matters is a sharp one: is the rattle in the hardware around the filter, or in the filter itself?

The two have very different consequences. A loose heat shield is a ten-minute job. A broken filter core can let soot through, shed debris into the silencer and turbocharger side of the system and cost the filter. The trouble is that both can sound alike through a canister wall. This guide gives you a method for telling them apart without damaging anything, a clear list of what to do and what to avoid, and decision points that say when to stop investigating and call the supplier.

The advice is general. Your supplier’s manual and service instructions come first, and any internal inspection is for the supplier or an approved technician.

Why rattles happen in a canister that has no moving parts

An RECD has no moving parts in normal operation, so a rattle means something has come loose, broken or worn. That “something” tends to belong to one of three layers.

Layer 1: External hardware. Heat shields, covers, cable trays, brackets, lifting lugs, pipe hangers, clamps and fasteners on the outside of the canister and the pipework around it.

Layer 2: Interface and internal hardware. Parts that are inside or part of the canister, but not the filter core itself: baffles, cones, internal flow distributors, catalyst stage supports, inlet or outlet diffusers, mounting bands and retaining rings, inspection doors and their hardware.

Layer 3: The filter core and its mounting. The ceramic or metal substrate (the “brick”), the mat that holds it in the canister, and the seals that stop gas going around it. A broken brick, a cracked piece, a mat that has degraded and lets the core move, or a loose catalyst section all rattle.

Most rattles are in Layer 1, some in Layer 2 and a minority in Layer 3. That order is the order of likelihood and the order of cost, and it is the order in which to investigate.

Why the filter core might move

To understand Layer 3, it helps to see how the core is held. A ceramic filter core is brittle. It is wrapped in an intumescent or fibre mat that expands when heated, gripping the core against the canister wall. The mat has two jobs: it holds the core in place against vibration and flow, and it seals the gap so that exhaust cannot bypass the filter. If the mat is damaged, eroded, contaminated with oil or fuel, crushed by a bad assembly or burnt away by an uncontrolled burn, the core can shift. A DPF-recovery specialist describes this kind of case: if the filter body moves, the retaining mat breaks away because it is no longer clamped between the core and the canister, and the loose mat fibres disperse downstream. Moving cores can also crack from the shock of knocking against the shell.

Other ways a core ends up rattling:

A fleet-magazine article describing two truck failures reports that the DPF outlet cracked and large chunks fell into the exhaust, yet no fault code had flagged anything and it was found only on inspection. That is a vehicle example, but it carries a useful message: a damaged core can keep running without any alarm, so noise may be the only warning.

Start with what the rattle does

Before touching the canister, collect the behaviour of the sound. These observations cost nothing and sort the layers.

When is it heard?

WhenWhat it suggests
At cold start, then fades as the system warmsA loose part that is held by thermal expansion once hot, such as a bracket or shield, or a cracked part whose pieces swell into contact
At idle or low load onlyA low-energy rattle of a loose item, since stronger pulses at high load may hold or mask it
At a particular load band onlyResonance of a shield, cover or loose part with the engine’s pulse frequency
When the set is stopped and during run-downA loose part moving as the exhaust pulses fade, or a core piece settling
When the set is stopped and the canister is moved or struckA free part inside
Only when hotDistortion or thermal growth of a shield, cover or support
During or just after regenerationHeat-induced movement, possibly a cracked core, a loosened internal part or a heater element support

What does it sound like?

DescriptionTypical source
Light, metallic tinkle or chatterThin shield, loose clip, cable tie, thin cover
Heavy, hollow “bonk” or knockLoose bracket, a loose support frame or the whole canister moving in its mounting
Sandy or gravelly shifting, like gravel in a tinFragments or loose fibres inside; material moving when the canister tilts
Single sharp “clack” when load changesA part shifting under pulse changes
Rhythmic ticking in time with firingOften a leak, not a rattle; see exhaust leaks around an RECD

Gravel-like or sandy sound with the canister at rest is the most worrying, because it suggests loose pieces inside. A loose bolt or shield rarely sounds like that.

Does it change with a regeneration?

A sound that appears or changes during a regeneration cycle, particularly one that follows a failed or interrupted cycle, deserves attention. Check the log for the preceding events. Our article on interpreting an RECD regeneration completion message explains how to read cycle records.

Layer 1: external hardware checks

All checks in this section are for a cold, isolated system. Use lock-out and tag-out, and let the exhaust cool fully.

Heat shields and covers. Press and shake each shield by hand. A shield that moves or buzzes is a candidate. Truck-maker bulletins on noisy after-treatment units repeatedly list heat shields on the inlet, loose covers on the filter housing and loose brackets among the first things to check. Look for broken spot welds, missing fasteners, distorted edges and shields rubbing the canister.

Brackets and support frames. Check every bracket that connects the RECD or pipe to the structure. A bracket whose weld has cracked is a common source of a heavy rattle, and vehicle bulletins describe cracked DPF brackets and broken mounting points as the cause of rattling noises. Look for hairline cracks at welds, loose bolts and worn rubber isolators. Check that the frame is bolted down. See wall-mounted versus floor-supported RECD support layout.

Pipe hangers and clamps. A hanger that has lost tension lets the pipe move and tap. Check each hanger is carrying load.

Cables, conduits and sensor lines. A loose conduit or sensor tube can tap on a pipe. Our guide to RECD cable routing near hot exhaust lines explains how they should be fixed.

Bellows and liners. A flexible section with a loose liner can rattle. See flexible bellows in an RECD exhaust system.

Fasteners. Check torque on flange bolts, support bolts and cover screws. Loose bolts rattle in their holes and also signal that a joint is under strain.

If a Layer 1 fix removes the sound and it stays gone after a loaded run, you are done. Photograph the repair and note it in the log.

Layer 2: interface and internal hardware

If the outer layer is quiet, the next suspects are parts inside the canister or in the flow path that are not the core. Some of these can be seen without dismantling the filter.

  • Inlet and outlet cones and diffusers. A cone that has cracked at a weld, or a flow distributor that has come adrift, can rattle at some flows.
  • Internal baffles or perforated tubes. Some designs include them; a failed support lets the part move.
  • Catalyst stage in designs with a separate oxidation catalyst. A loose catalyst brick or a cracked retaining ring will rattle.
  • Heater element supports in heater-assisted designs. A broken support or a loose element sheath can rattle, and it is also a risk for electrical faults.
  • Door and cover internals, such as a loose gasket retainer or a loose bolt dropped inside during service.
  • Foreign objects. A nut, washer or tool left inside during assembly is a classic. Our guide to closing an RECD punch list before handover includes a tool and material count for this reason.

Some of these can be checked through inspection openings with a torch and a borescope, but only with the supplier’s instruction. Opening a canister, removing a core or disturbing a heater element should be done by trained people with the right gaskets and procedure.

Layer 3: the filter core

If Layers 1 and 2 are clear and the rattle remains, you must consider the core and its mounting. Warning signs that make Layer 3 more likely:

  • A gravel-like sound that moves when the canister is tilted or struck when cold.
  • A rattle that began after an interrupted or failed regeneration, a thermal event or an impact.
  • A falling ΔP at constant load, which suggests that gas is bypassing the core or that a section has broken. Compare against the commissioning figure at the same load; see comparing RECD pressure readings at different generator loads.
  • Soot or ceramic dust visible at the outlet side, or a change in smoke. See black smoke after RECD installation.
  • Fibres or ceramic fragments in the silencer or at drains.
  • Increased noise after a transport event or after the canister was lifted.

None of these is proof. Several have other causes. Together with a rattle they are enough reason to stop trying things and call the supplier.

The cold tap test: what it can and cannot tell you

A tap test is a cautious way to learn something about the canister without opening it. It must be done on a cold, isolated system.

Equipment. A soft-faced mallet or the heel of your hand, a torch, a phone to record audio and an assistant to note the sounds. Do not use a steel hammer.

Method.

  1. Confirm lock-out, cool system and a stable, safe position.
  2. With the heel of your hand, give a firm but gentle push on the canister side and listen. A hollow knock or shifting sound suggests something free.
  3. Tap lightly along the canister with a soft mallet, in a line from inlet to outlet, and listen for a change in tone. A uniform dull sound is normal for a well-packed core, since the mat and ceramic dampen sound. A rattle or “loose” sound at one spot suggests something free there.
  4. Where it is safe and the supplier allows, tilt or rock a small, light canister gently. Do not do this with a large installed unit.
  5. Record the sounds and mark the positions.

What it cannot do. A tap test cannot prove a core is sound, and a silent test does not rule out a crack. A tap that makes a loose sound does not tell you whether a core is cracked or a bracket is loose. It is a screening step.

Never.

  • Strike a canister hard. You can crack a good ceramic core.
  • Shake or knock a unit hoping to “settle” or clear loose pieces. If pieces exist, moving them can cause more damage or move them toward the silencer or turbo.
  • Open a canister and reach in without the supplier’s procedure.
  • Remove any component of the core’s mounting.

The decision flow

Think of the whole process as a sequence of gates. At each gate, the question is whether the rattle has been explained and cured.

  1. Is the system safe to approach? Cold, isolated, tagged. If not, stop.
  2. Layer 1 checks complete? Shields, covers, brackets, hangers, cables, fasteners. If you find and fix a loose part and the rattle ends, record and finish. If the rattle persists, go on.
  3. Layer 2 checks complete? Visible interface parts, doors, internal items. If you find a loose or fallen part (for example a dropped nut), the supplier should retrieve it and check for damage. If nothing is found, go on.
  4. Does the behaviour or the data point to the core? Sandy sound, tap test loose sound, ΔP falling or smoke changing, a history of interruption or impact? If yes, stop and call the supplier.
  5. Is the set safe to keep running? Ask the supplier. If a core is damaged, running can cause further damage, and debris may reach downstream parts. Follow the supplier’s instruction on load, running time and isolation.

If your site has a bypass arrangement, the supplier can tell you whether it is acceptable to use it temporarily, and what the compliance consequences are. Do not assume it is.

What the supplier will probably ask for

A good report gets a faster answer. Prepare:

  • The engine and RECD models, serial numbers and installation date.
  • A description of the sound: when it occurs, what it sounds like and how it changes.
  • Audio recordings taken at a fixed position and load.
  • Photographs of the canister, supports, shields and the downstream pipework.
  • The ΔP and temperature logs for the last two months, with load noted. See the RECD event log for a format.
  • The regeneration history, including any failed or interrupted cycles and any alarms.
  • A list of what was done recently: service visits, cleaning, handling, lifting, engine work.
  • Results of your Layer 1 and Layer 2 checks.

Our article on what to record for an RECD warranty claim explains how this evidence supports a claim, and the RECD alarm response matrix offers a way to decide who to call and when.

Core damage: what happens next

If an inspection confirms a damaged core, the supplier will explain the options. Typical choices are:

  • Replace the filter core and keep the canister if it is undamaged. See filter core versus complete assembly replacement.
  • Replace the complete assembly where the canister, mat or supports are also damaged.
  • Refurbish only where the supplier confirms that it is safe and suitable. A cracked ceramic core is generally a replacement case, and our article on refurbished RECD filter core reuse explains why caution is needed.

A damaged core also raises the question of why it was damaged. If the cause was a violent regeneration, repeated interruptions, wet stacking or an overloaded filter, a new core will face the same conditions unless the duty or the engine is corrected. See RECD regeneration after wet stacking and why an RECD keeps clogging.

Downstream debris is another concern. If pieces of ceramic or mat fibre have passed into the silencer or stack, they should be cleared. Ask the supplier how to check for them and how to handle them safely, since the material can be hazardous dust. Our guide on handling soot and ash removed during RECD servicing covers safe handling.

A worked illustration: three rattles, one of them serious

The following is an illustrative scenario, not a real site. A hospital maintenance team has three sets with RECDs fitted at the same time. Within a month, three different rattles are reported.

Set A. A light, tinny rattle at idle that vanishes above 40% load. Cold inspection finds a cable-tray bracket with a loose bolt resting against the silencer. The bolt is tightened, and a spacer fitted. The sound does not return after a month. This was Layer 1.

Set B. A heavy knock at start-up that fades after fifteen minutes. A support bracket’s weld has a hairline crack. The supplier re-welds and adds a gusset. Layer 1 again, although the bracket was part of the canister mounting.

Set C. A gravelly shifting sound when the canister is gently pushed when cold, and a recorded rattle at a steady 50% load. The team notes that ΔP at 50% load has fallen from 30 to 22 mbar over six weeks, with no change in the load profile, and that three regeneration cycles were interrupted by grid transfers in the same period. The tap test gives a loose sound near the middle of the canister. The team stops, tags the set out of service as far as operations allow and calls the supplier. An inspection finds a cracked core with a degraded mat, and a small amount of ceramic in the silencer. The core is replaced, the silencer is cleared and the plant arranges loaded runs after outages so that regeneration is not interrupted.

The important lesson from Set C is that the team did not try to cure the problem by tapping, shaking or running it harder. They used the pattern of sound, ΔP and history to recognise a Layer 3 problem, and they stopped.

Preventing rattles

  • Support the canister properly. The pipework should not carry the weight. See wall-mounted versus floor-supported support layouts.
  • Handle and lift according to the supplier’s instructions, and inspect on delivery. See the delivery inspection checklist.
  • Protect the cycle. Avoid repeated interrupted regenerations, which stress the core. See when the generator stops during RECD regeneration.
  • Keep soot loads within limits, so that a violent burn is less likely.
  • Fix oil, fuel and coolant leaks that reach the exhaust, because they contaminate the mat.
  • Count tools and loose parts at the end of every service visit.
  • Record a baseline sound at commissioning and after major service.
  • Use a checklist for external hardware at each quarterly inspection, including shield fixings and brackets.

Frequently asked questions

Can a loose heat shield damage the RECD?

Directly, rarely. A shield rubbing the canister can wear a spot over time, and a shield that falls into the exhaust path can cause damage. It is a nuisance that is quick to fix.

Should I keep running a set with an unexplained rattle?

If the sound is clearly from external hardware, such as a loose shield, you can usually run until a convenient repair time. If it may be from inside, ask the supplier before running further, since a damaged core can fail progressively.

Can I check inside the RECD myself?

Not unless the supplier’s manual and training allow it. Opening a canister risks damaging the mat, contaminating the core and exposing people to hazardous dust. Request a supplier inspection.

Does a quiet canister mean the core is intact?

No. A core can be cracked and still be silent, and a rattle can come from hardware. Use the pressure trend, smoke behaviour and history together.

How is a rattle different from a leak sound?

A leak usually ticks, puffs or hisses in time with the engine and leaves soot around a joint, while a rattle is a mechanical clatter that depends on movement. See whistling after RECD installation for flow-induced tones.

Bringing it together

A rattle inside an RECD is one of three layers: external hardware, interface and internal parts, or the filter core and its mat. Work through them in order of likelihood and cost, using the behaviour of the sound, cold checks and the ΔP and smoke record. Fix loose hardware yourself where it is safe, avoid striking or shaking the canister, and when the evidence points to the core, stop, preserve the evidence and call the supplier.

If you would like help interpreting a noise log or reviewing your supports and handling procedure, see our retrofit emission control devices, check the certifications or contact the Aceget team.

Related Reading

Sources



1 Comment

Leave a Reply