- November 14, 2026
- Posted by: editor
- Category: RECD & Emission Control Devices
A catalysed RECD is not a static part. Its filter body may look the same after five years, but the thin precious-metal layer that helps soot burn at modest exhaust temperatures slowly changes. The short answer to the question in the title is yes: catalyst aging can change an RECD’s regeneration behaviour, usually gradually, usually by making passive regeneration harder and assisted regeneration more frequent or longer.
The longer answer is more useful. Different ageing mechanisms leave different fingerprints in your data. Some are inevitable, some are accelerated by how the set is run and some can be reversed or mitigated. This article gives a timeline view of what tends to happen over the life of a catalysed device, explains the three main routes by which a catalyst loses effectiveness, links each to symptoms in the regeneration log and ends with a practical decision path.
Not every RECD has a catalyst. Some are uncatalysed filters that rely on heat or assisted regeneration, and some add a separate oxidation catalyst stage. Everything here applies only where a catalyst is present. If you are unsure about your own device, ask your supplier. Our article on catalysed versus uncatalysed RECD filters explains the difference.
What the catalyst is doing for regeneration
A catalyst in a retrofit filter usually plays two roles.
- It oxidises carbon monoxide and hydrocarbons once the exhaust is warm enough, which cuts odour and gaseous emissions.
- It converts part of the nitric oxide (NO) in the exhaust into nitrogen dioxide (NO2). NO2 is a stronger oxidiser than oxygen and burns soot at lower temperatures. This is the basis of NO2-assisted passive regeneration, described in DieselNet’s overview of particulate filter regeneration.
If the catalyst loses activity, both jobs suffer, and the second one is what changes regeneration behaviour. Less NO2 means soot needs higher temperatures to ignite. At moderate load the exhaust may be warm enough only for catalyst-assisted burning, so the window in which passive regeneration works shrinks.
Published research supports this link. A 2025 SAE paper on reduced catalytic activity and passive regeneration of catalysed particulate filters reports that impaired catalytic activity can have a significant impact on regeneration, and that adding an upstream oxidation catalyst, which raises NO2, partly offset the effect of ageing in the tests. A review of long-term filter performance in heavy-duty vehicles, indexed by the Transportation Research Board, reports that filters collected from the field showed a marked loss of NO conversion from catalyst poisoning, which created less favourable conditions for low-temperature regeneration. These studies concern vehicle systems rather than stationary generators, so they show the mechanism, not the rate for your set.
The three routes to a tired catalyst
Different causes leave different clues, so name them before diagnosing.
Route 1: Thermal ageing (sintering)
What happens. Precious-metal particles on the washcoat grow larger when exposed to high temperature, and the washcoat itself can lose surface area. Fewer, larger particles present less active surface, so conversion at a given temperature falls.
What speeds it up. Repeated high-temperature excursions: very hot regenerations, runaway burns, long runs at very high load and frequent assisted cycles at the upper end of the temperature range.
How significant. A European study on ageing of emission control systems concluded that thermal deactivation is the main pathway of ageing for most catalytic aftertreatment devices, with ash plugging next in importance for some. For filters, ash deposition is the dominant degradation route. The report is available through CORE and discusses these mechanisms across device types.
Fingerprint in the log. A gradual rise in the temperature needed for regeneration to start or finish, and a gradual loss of the catalyst’s temperature rise (if you measure outlet versus inlet), often with no sudden step.
Route 2: Chemical poisoning
What happens. Compounds from fuel and oil, mainly sulphur, phosphorus and zinc, bond to active sites or form deposits that block them. Our article on how catalyst poisoning can affect an RECD covers this in depth.
What speeds it up. High oil consumption, high-ash oil, higher-sulphur fuel and engines that burn oil.
How significant. In an SAE study on thermal and chemical ageing of diesel particulate filters, the thermal ageing conditions tested had only a minor effect on filter performance, while chemical ageing by phosphorus had a significant effect on regeneration capability. Different conditions give different results, but the lesson is that oil chemistry deserves attention.
Fingerprint in the log. A faster decline than thermal ageing alone would explain, correlated with oil consumption or fuel source, and sometimes a step change after a change in oil or fuel.
Route 3: Masking and fouling
What happens. A physical layer covers the catalyst without chemically changing it. Ash, oily soot or heavy-fuel residues act as a film that stops exhaust reaching the active sites.
What speeds it up. Wet stacking, oil carry-over and long light-load running.
How significant. It is potentially reversible. If cleaning or a controlled burn removes the layer, activity may return. Our article on RECD regeneration after wet stacking covers one cause.
Fingerprint in the log. Symptoms that worsen during light-load periods and partly recover after a hot, loaded run or a cleaning.
The fourth player: ash
Ash is not a catalyst problem in the strict sense, but it interacts with it. Ash accumulates in the filter and cannot be burned away. Over time it reduces the usable filter volume, raises back-pressure and can cover catalyst surfaces. Our guide to soot versus ash in RECD regeneration explains why regeneration cannot fix it.
What field and bench studies say about ageing
An open-access study of catalysed filters aged on urban buses found that characteristic temperatures for CO and propane conversion and for NO2 production rose after ageing, and that platinum-palladium coatings can lower soot light-off from about 450–550 °C to roughly 250–300 °C when NO2 is present. It also reports that adding palladium or rhodium to platinum helps limit particle sintering (Scientific Reports, via PMC). The bus conditions differ from a DG set, but the direction matches what this article describes: ageing shifts the temperature at which passive regeneration works, so ask the supplier which coating formulation your device uses.
A timeline of what usually changes
The table below is a generalised story of a catalysed RECD on a DG set with moderate use. Real devices vary widely with duty, oil, fuel and design. Use it as a hypothesis about direction, not as a prediction of timing.
| Stage | Approximate age or use | What tends to happen to the catalyst | What operators may notice |
|---|---|---|---|
| Fresh and settling | First weeks to a few months | Initial conditioning; some early loss of surface area as the catalyst stabilises | Regeneration behaviour settles to a baseline; record it |
| Stable period | First years | Slow, steady decline in activity | Little change; baseline holds if duty is steady |
| Gradual decline | Middle years | Cumulative thermal ageing and slow poisoning | Passive regeneration needs more load or time; ΔP at reference load drifts up; assisted cycles become more frequent |
| Noticeable shift | Later years, or earlier under harsh duty | Lower NO to NO2 conversion; higher light-off temperature | Regeneration works only in the upper part of the load range; odour may return at light load |
| Late stage | End of useful catalyst life | Little remaining activity; masking and ash worsen things | Frequent or long assisted cycles, high end ΔP, back-pressure alarms, request for cleaning or replacement |
None of these stages has a fixed number of hours. Ask your supplier for the expected catalyst life under your duty and what they consider the end-of-life indicator.
Reading ageing in the regeneration log
Because the catalyst is hidden inside the housing, you infer its condition from behaviour. These are the signals to watch, with the likely meaning of each.
| Signal | What ageing would look like | Other possible causes to rule out |
|---|---|---|
| Reference ΔP drifts upward over many months at the same load | Passive regeneration clearing less soot | More soot from the engine, ash accumulation, sensor drift |
| Regeneration cycles become more frequent | Less passive clearing between cycles | Duty change, light-load running, engine soot increase |
| Cycle duration rises | Soot ignites later or burns slower | Weak heater, wet insulation. See what a rising regeneration duration tells you |
| Minimum load for stable ΔP rises | Catalyst needs hotter exhaust | Cooler ambient, insulation loss |
| Temperature rise across the catalyst shrinks (if measured) | Lower oxidation of CO and HC | Sensor placement, flow changes |
| Odour of unburnt fuel returns at light load | Lower CO and HC conversion | Wet stacking, injector problems |
| Outlet NO2 or opacity changes (if measured) | Lower NO2 production | Instrument error, load difference |
| Step change after oil or fuel change | Poisoning or masking | Change of engine tune at the same time |
Single readings mislead. A trend over many months at a fixed reference load is more useful. See our seasonal tracking guide for passive RECD regeneration for how to separate seasonal effects from slow drift.
Illustrative example: how a shifted ignition temperature changes the load window
The numbers here are invented to show the logic and are not measurements of any product.
Suppose a fresh catalysed filter supports passive regeneration whenever the filter inlet exceeds about 330 °C for a sustained period. For a particular DG set, that inlet temperature is reached at roughly 35% load or higher.
After several years, suppose the catalyst’s ability to produce NO2 has dropped so that a similar soot burn rate now needs about 30 °C more at the inlet, say 360 °C. On the same engine, that temperature might only be reached at about 45% load.
| Condition | Inlet temperature needed (illustrative) | Load needed for it (illustrative) | Share of site’s run hours above that load |
|---|---|---|---|
| Fresh catalyst | 330 °C | 35% | 55% |
| Aged catalyst | 360 °C | 45% | 38% |
The site’s duty pattern is unchanged, but the share of hours in which passive regeneration works drops from 55% to 38%. That is a 17 percentage-point loss, so more soot accumulates, ΔP at reference load rises, assisted cycles become more frequent and the operator concludes that “the filter is getting worse”. The filter is not necessarily blocked. The window simply narrowed.
That is why load logs matter. If you can see the share of hours above the new threshold, you can decide whether to change the duty (concentrate load), add assisted regeneration, refurbish or replace the catalyst. Our guide to using DG load logs to assess RECD suitability shows how to build the table.
What accelerates ageing, and what you can control
Some factors lie outside your control. Others are well within it.
Factors you can influence
- Oil quality and consumption. Use the grade the engine and RECD supplier recommend, usually a low-ash formulation where specified, and fix oil consumption problems. See engine oil consumption and RECD suitability.
- Fuel quality. Buy from reliable sources, store fuel properly and note any change in supplier. Sulphur content matters for poisoning. See also biodiesel blends and RECD-equipped generators.
- Duty cycle. Avoid long idling and very light load, which foul the catalyst.
- Regeneration discipline. Avoid runaway burns by not letting soot load climb to extremes. See can repeated failed regeneration damage an RECD filter.
- Engine health. Injectors, turbo and air supply that produce less soot and less unburnt fuel reduce stress on the catalyst.
- Thermal protection. Intact insulation and correct installation limit temperature swings. See RECD insulation and heat shields.
Factors that are mostly built in
- Exposure to ordinary exhaust temperatures over thousands of hours.
- The design’s precious-metal loading and washcoat choice. Catalyst durability is a design property.
- Normal ash accumulation from oil additives, which is slow but cumulative.
From suspicion to decision: a practical path
When ageing is suspected, follow a staged approach and avoid jumping to replacement.
Step 1: Confirm with data
Gather twelve months or more of reference ΔP, regeneration frequency and duration, load bands, temperature readings and events. Check whether the drift is steady or steps with events. Make sure sensors are healthy; see separating a sensor fault from an RECD performance problem.
Step 2: Remove the easy causes
Check insulation, heater supply, engine soot production, oil and fuel changes, and duty changes. Compare with the commissioning baseline.
Step 3: Distinguish reversible from irreversible
Ask the supplier whether a supervised hot, loaded run, a cleaning or a refurbishment is likely to help. If masking or oily soot is the issue, recovery may be possible. If thermal sintering or poisoning has occurred, recovery is limited.
Step 4: Ask for a catalyst activity check
Some suppliers can assess catalyst condition by measuring conversion across the device, by comparing temperature rise across the catalyst, or by testing a sample. Ask what they offer and what it costs. For related test methods, see RECD testing during regeneration: what to record.
Step 5: Choose among options
| Option | When it makes sense | Considerations |
|---|---|---|
| Change the duty or load pattern | Window has narrowed but device is otherwise healthy | Operational discipline; may not be possible everywhere |
| Add or increase assisted regeneration | Passive window too small for the duty | Energy cost and heater or burner wear; see electric-heater versus fuel-assisted regeneration |
| Clean or refurbish the filter | Masking or ash suspected | Does not restore sintered or poisoned catalyst. See refurbished RECD filter core reuse |
| Replace the filter core or catalyst stage | Activity is low and cannot be recovered | Cost and downtime; see filter core versus complete assembly replacement |
| Replace the whole device | Obsolete or mismatched design | Re-assessment of duty; see discontinued RECD model parts support planning |
Step 6: Re-baseline
After any action, record a new baseline: reference ΔP, temperatures, time to working temperature and regeneration behaviour. Keep it with the history.
Design and buying questions about catalyst life
If you are buying a catalysed device, or reviewing a quote, ask the supplier:
- What catalyst type and loading is used, and what is the expected life at my duty cycle?
- How is catalyst condition checked in service?
- What oil and fuel specifications protect the catalyst?
- What temperature excursions does the catalyst tolerate and for how long?
- Does the warranty cover catalyst activity, and how is loss of activity measured and defined?
- Is the catalyst replaceable separately from the filter?
- What evidence is there from similar sets after several years in service?
Our guide on RECD performance guarantees and operating conditions shows how to tie such answers into the contract. Aceget’s product pages describe silicon carbide filters with a precious-metal coating and an oxidation catalyst stage designed for NO2-assisted regeneration; if you want the documents behind any catalyst-life statement, ask us through the contact page and see the certifications page.
What ageing means for emission test results
A catalyst that has aged will not necessarily change the particulate result of a test, because the filter body does most of the capturing. But it can change other things that a test report may show.
- Gaseous results. Carbon monoxide and hydrocarbon conversion may fall, particularly at light load or after cold starts. If your original report showed good CO and HC reduction, a later test may not repeat it.
- NO2 share. If NO2 is measured, a lower share is a direct sign of reduced NO oxidation.
- Timing against regeneration. A device whose catalyst has aged may spend more time loaded, so a test taken at the end of a long soot-loading period can show a different result from one taken just after a cycle. See RECD efficiency in new versus aged condition and when to retest an RECD after DG set changes.
Whenever you retest, record the load, the time since the last regeneration, ΔP and temperatures. Without them, a changed result cannot be attributed to ageing, wear or a different operating state.
A fleet view: comparing sets of different ages
If you manage several sets, ageing becomes a portfolio question. Plot reference ΔP, cycles per 100 run hours and minimum stable load for each device against its age and run hours. Sets that sit well above the pack for their age may have an engine, oil or duty problem. Sets that track the pack are probably ageing normally. This view helps you decide where to spend inspection effort first, and it feeds budget planning for refurbishment or replacement. See RECD fitment in a mixed-make, mixed-age DG fleet and the shared spare RECD for a generator fleet.
Common misunderstandings
“If the catalyst ages, the filter stops working.” The filter continues to trap particulates. What changes is how easily the trapped soot burns away.
“A catalyst lasts forever.” It lasts a long time under benign conditions, but it is a consumable layer on a durable body. Catalyst life varies with oil, fuel and duty.
“Higher regeneration temperature is always better.” Hotter cycles may burn soot faster but accelerate thermal ageing and risk filter damage.
“Replacing the filter fixes the engine.” A new filter on an engine that produces oily soot or burns oil will age quickly. Fix the source as well.
“Passive regeneration decline means the DG is too small.” It may mean the DG runs at lower load than before, the catalyst has aged, or both. Check the load log first.
FAQ
How long does an RECD catalyst last?
There is no single figure. Life depends on the catalyst design, oil, fuel, duty cycle and temperature history. Ask your supplier for an estimate at your duty and monitor trends in your own data.
Can catalyst aging be reversed?
Partly. Masking by oily soot or deposits may be reduced by cleaning or a supervised hot run. Thermal sintering and chemical poisoning are largely permanent, though some sulphur effects can be partly reversible under the right conditions. A supplier or catalyst specialist can advise on your case.
Will ageing increase my emissions?
It can reduce conversion of carbon monoxide and hydrocarbons and may change the NO2 fraction. Particulate capture by the filter itself generally continues, but if soot accumulates unchecked, back-pressure and other problems follow. An emission test shows the current state. See calculating RECD particulate reduction.
Does the catalyst affect NOx reduction?
Not materially. The catalyst mainly changes the split between NO and NO2 rather than removing nitrogen oxides. Our article on whether RECDs reduce NOx explains this.
How do I know it is the catalyst and not the heater?
Compare the heater’s current and on-time with commissioning data, check insulation and supply, and look at whether the passive regeneration window shrank. If the heater behaves normally and passive regeneration is weaker, the catalyst is a likely suspect. A supplier test can confirm.
Should I plan a catalyst replacement in advance?
Plan for it in the asset register and budget, using the supplier’s life estimate and your own trend data. See RECD asset register for a multi-site DG fleet.
Bringing it together
Catalyst aging changes an RECD’s regeneration behaviour mainly by narrowing the conditions in which passive regeneration works. It arrives through thermal ageing, chemical poisoning and masking, with ash as a companion problem, and it shows up as a slow drift in reference ΔP, longer or more frequent cycles and a higher load needed for stable operation. Track your trends, rule out easy causes, separate reversible from irreversible effects and plan the response before the device reaches a crisis.
To discuss catalyst options and duty matching for your DG set, explore our retrofit emission control devices, read the DG set emission regulations guide or contact the Aceget team.