- November 16, 2026
- Posted by: editor
- Category: RECD & Emission Control Devices
“We’ll bake it” sounds reassuring. It conjures an image of a clean, controlled oven doing what an engine cannot, burning off everything that clogs the filter. In many cases that picture is roughly right. Thermal treatment is a standard step in professional filter cleaning, particularly for oily or carbon-rich deposits, and trade sources describe it as the first stage of a “bake and blow” process in which the element is heated to oxidise leftover soot and then blown out to remove ash (Trucksales).
But heat is also the most dangerous thing you can do to a ceramic filter that carries a catalyst coating and a load of burnable material. Too fast, too hot, too uneven or too long, and the element can crack, the coating can age and the ash can fuse into something harder to remove than before. So thermal cleaning of RECD filters is not a yes-or-no service. It is a process, and the quality of the process is in the details: the temperature profile, where the temperature is measured, how the burning of soot is controlled and what happens afterwards.
This article is a briefing for the owner who must judge a provider. It explains what thermal cleaning can and cannot do, why heat is risky, then gives you fourteen questions in three groups (before the oven, in the oven and after the oven), a bake-profile sheet with worked arithmetic, red flags and a scoring method that turns the answers into a decision. Details differ by element and supplier, so treat the numbers as illustrations and the supplier’s approved procedure as the authority.
What thermal cleaning does, and what it does not
It does:
- Oxidise soot left in the channels, turning carbon into gas.
- Drive off volatile and oily material, in a staged process, so that sticky deposits can be removed afterwards.
- Loosen carbon-bound ash, so it can be removed by air or other means.
It does not:
- Remove ash. Ash is incombustible. After the bake, it is still in the filter. This is why “bake and blow” has two parts, and why a bake with no second stage is not a full cleaning. See soot versus ash in RECD regeneration.
- Repair damage. Cracks, melts and failed seals are not cured by heat.
- Restore a tired catalyst. If anything, over-temperature can accelerate catalyst ageing. See catalyst ageing and RECD regeneration behaviour.
How long does it take? Reported figures vary because designs vary. A trade article quoting a cleaning-equipment maker gave about nine hours for the thermal cycle of one machine (FleetOwner), another source describes the baking stage as lasting from 4 to 24 hours depending on the design (Overdrive), and a truck-dealer article says a thermal cleaning typically takes about a day including heating and cool-down (Rush Truck Centers). Those are truck-filter numbers. For your element, the supplier’s approved profile decides.
Why heat is risky for a ceramic filter
Four mechanisms account for most of the damage that thermal cleaning can do.
1. Thermal shock
Ceramics tolerate high temperatures but not steep temperature differences. Heat the outside quickly while the core stays cool, or cool the element too fast, and the walls can crack. This is why proper profiles specify slow ramps and controlled cooling, and why opening the oven door early is a mistake.
2. Runaway burning of soot (exotherm)
Burning soot releases heat. A thick soot load, or a load rich in oily material, can release a lot of heat quickly, pushing local temperatures well above the oven setpoint. DieselNet’s overview of diesel particulate filter regeneration explains that the soot load at the start of a burn governs the peak temperatures reached. In an oven, the answer is to control how fast the soot burns, by controlling temperature ramp, oxygen supply or both. Ask how it is done.
3. Catalyst ageing
Precious-metal particles on a catalyst coating grow larger at high temperature, which reduces active surface area. A thermal cleaning that exceeds the coating’s tolerance does not just fail to help. It shortens the life of the catalyst. Our article on catalysed versus uncatalysed RECD filters explains what the coating is for.
4. Ash fusion and glazing
At high temperatures, ash can sinter or fuse into harder masses that resist later cleaning. A proper profile avoids unnecessary peaks, and a provider should know the difference between “hot enough to burn soot” and “hot enough to damage”.
Fourteen questions in three groups
Group A: Before the oven
Question 1: Is thermal treatment approved for my element and its coating?
The supplier’s guidance outranks everything else. Ask for the approved temperature range and the maximum number of thermal cycles, in writing. If the supplier has no guidance, ask the provider to show where their parameters come from.
Good answer: a reference to supplier guidance or documented testing for this element type. Poor answer: “We bake everything the same.”
Question 2: How do you screen the element before it goes in?
A cracked element can fail catastrophically in an oven, and an element soaked with oil is a fire and smoke risk. Screening should include inspection of both faces and the housing interfaces, weighing and, ideally, a flow test.
Good answer: a documented intake inspection with photographs. Poor answer: “It goes straight in the oven.”
Question 3: What happens to wet, oily or fuel-soaked elements?
Elements from engines that suffered wet stacking carry liquid fuel and oil. Putting them straight to a high temperature creates smoke and a risk of rapid burning. Our article on RECD regeneration after wet stacking explains how these deposits arise. A careful provider uses a low-temperature stage to drive off liquids before the main burn.
Good answer: a staged profile with a low-temperature hold, or a separate pre-treatment. Poor answer: no distinction between dry and oily elements.
Question 4: Do you weigh and record the element before and after?
Weight change across the bake shows how much combustible material burned off. It is also an independent check on the profile. Weight records should include the scale and the date.
Group B: In the oven
Question 5: What is the temperature profile?
Ask for the profile as a table: starting temperature, ramp rates, hold temperatures and times, peak temperature, soak time and cooling rate. A provider who works from a documented profile can give you this. One who works by feel cannot.
Question 6: Where is temperature measured?
The oven’s air temperature and the element’s temperature are not the same. Elements lag the oven when heating and may exceed it when soot burns. The question to ask is whether temperature is measured on or in the element, and how many points.
Good answer: thermocouples placed on the element, with logging. Poor answer: “The oven setpoint is 550.”
Question 7: How is the oxygen supply controlled?
Soot burns when oxygen is available. Controlled airflow slows burn-off and prevents sudden peaks. Ask whether the oven supplies a metered air flow, and how the operator responds if the element temperature rises faster than planned.
Question 8: How uniform is the heating?
Hot and cold spots across the element lead to uneven burn-off and stress. Ask whether the oven has been mapped for uniformity and how recently.
Question 9: What are the limits and alarms?
A competent process has a maximum element temperature, a maximum rate of rise, and an alarm and response if either is exceeded. Ask what the limits are and what happens on an alarm.
Question 10: What happens to the off-gas?
Burning soot and oily material releases smoke, odour and gases. Responsible workshops treat or filter the oven exhaust. Ask where the gases go, whether there is an afterburner or filter and whether the workshop meets local emissions conditions. A poor answer here suggests poor control elsewhere.
Group C: After the oven
Question 11: What stage removes the ash?
A bake leaves ash. Ask what happens next, such as controlled air cleaning in an extracted cabinet or a wet process, and whether each stage is approved for the element. See why compressed-air cleaning may be unsuitable for some RECD filters and can you wash an RECD filter?.
Question 12: How do you test the result?
Expect a flow or pressure-drop test and a weight, compared with a reference and an acceptance limit. See RECD cleaning report: how to verify that the service was effective.
Question 13: How many thermal cycles has this element had, and what is the limit?
Each thermal cycle adds stress. Records of cleaning history help the provider and the supplier decide when an element should be retired. If you do not keep a cleaning log, start one, and see tracking RECD service cost per operating hour for the kind of record that makes lifecycle decisions easier.
Question 14: What happens if something goes wrong?
Ask how the provider handles an over-temperature event, a cracked element found after the bake, or an element that fails the flow test. Expect a documented response, a report to you and a clear statement of liability.
The bake-profile sheet: what a good record looks like
A provider with a real process can show you a record like the one below for your element. The values are illustrative only and not a recommendation for any element. Your supplier’s approved profile governs.
| Stage | From (°C) | To (°C) | Rate (°C/min) | Time (min) | Purpose |
|---|---|---|---|---|---|
| 1. Low ramp | 30 | 150 | 2.0 | 60 | Gentle warm-up, drive off moisture |
| 2. Low hold | 150 | 150 | n/a | 60 | Evaporate light liquids |
| 3. Main ramp | 150 | 550 | 3.0 | about 133 | Approach burn-off temperature |
| 4. Soak | 550 | 550 | n/a | 180 | Controlled burn-off of soot |
| 5. Controlled cool | 550 | 150 | 1.5 | about 267 | Avoid thermal shock |
| 6. Natural cool | 150 | below 60 | natural | per workshop | Handling temperature |
Check the arithmetic. Stage 1: (150 − 30) ÷ 2.0 = 60 minutes. Stage 3: (550 − 150) ÷ 3.0 = 133.3 minutes. Stage 5: (550 − 150) ÷ 1.5 = 266.7 minutes. The controlled stages add up to 60 + 60 + 133.3 + 180 + 266.7 = 700 minutes, which is about 11.7 hours before natural cooling. A provider who promises a “two-hour bake” for a heavily loaded element should be asked which of these stages they have removed, and why.
A good record also includes:
- Element identification and intake weight
- Thermocouple positions and the logged temperature trace for the cycle
- The actual temperatures and times, not just the planned profile
- Any alarms or deviations
- Weight after the bake, and the next stage with its own record
- Operator, oven identification and calibration status
Compare the logged trace with the planned profile. Large differences deserve an explanation. Our article on what to record in an RECD event log applies the same idea, a planned procedure beside a recorded outcome, to the on-site regeneration record.
Red flags
- No documented profile, or one that changes “depending on how it looks”.
- Oven setpoint treated as element temperature.
- A single standard bake for every element, regardless of coating, oil load or condition.
- No low-temperature stage for oily or fuel-soaked elements.
- Very short cycles promised for heavily loaded elements.
- No answer on off-gas.
- No second stage for ash, or a second stage that is an open-air blow.
- No before and after measurements.
- No cycle count or element history.
- A guarantee that sounds like a certainty, such as “will restore it to new”.
Scoring the answers: a worked comparison
To make the answers comparable, score each question 0 (no answer or poor), 1 (partial) or 2 (good, documented). Fourteen questions give a maximum of 28. The groups have different numbers of questions, so subtotals are shown.
| Group | Questions | Maximum |
|---|---|---|
| A: Before the oven | 1 to 4 | 8 |
| B: In the oven | 5 to 10 | 12 |
| C: After the oven | 11 to 14 | 8 |
| Total | 14 | 28 |
The following is an illustrative comparison of two providers for a coated element from a 400 kVA set.
| Group | Provider X | Provider Y |
|---|---|---|
| A: Before the oven (max 8) | 7 | 3 |
| B: In the oven (max 12) | 11 | 4 |
| C: After the oven (max 8) | 7 | 2 |
| Total (max 28) | 25 | 9 |
Provider X supplies a profile sheet, places thermocouples on the element, describes a low-temperature stage for oily elements, has an afterburner on the oven exhaust, follows the bake with extracted air cleaning and issues flow-test and weight records. It loses a point on the cycle-count question because it does not keep per-element history. Provider Y says it bakes overnight at a fixed temperature, cannot say where temperature is measured, has no second stage and offers a photograph as proof.
Suggested thresholds. 22 or more: proceed, subject to the supplier’s approval. Between 14 and 21: ask for the missing items in writing before agreeing. Below 14: decline. Treat any zero on the questions about supplier approval, screening or testing as a stop, whatever the total. The thresholds are suggestions to adapt.
When thermal cleaning is the right tool
Thermal treatment makes most sense when:
- Deposits are oily or carbon-rich and will not move with air or water.
- Pressure at the reference load stays well above baseline after verified regenerations, and inspection suggests residue as well as ash. See RECD regeneration vs filter cleaning: which service is needed.
- The supplier approves it and the provider can document control of the process.
It makes less sense when:
- The only issue is loose, dry ash. Air or another method may do the job with less thermal stress.
- The element is cracked, glazed or has a history of over-temperature events.
- The catalyst is ageing and the owner expects the bake to restore it.
- The provider cannot control or record the process.
How to prepare, and what to do afterwards
Before sending the element:
- Record pressure at the reference load, with date, load and run hours.
- Photograph both faces and the housing.
- Pack and seal the element to avoid shocks and dust.
- Give the provider the element’s identity, history and any known contamination, such as oil or fuel.
- Agree the profile, acceptance limits and records in writing.
After refit:
- Read pressure at the reference load during the next runs and compare it with the “before” value and the supplier’s nominal clean value.
- Watch regeneration behaviour for several cycles.
- File the provider’s profile, trace and test records with the asset record.
- Update your cleaning log and cycle count.
- If pressure is not where you expected, follow why RECD pressure can stay high after a cleaning service.
For an overview of how this fits with the choice of venue and method, read RECD filter cleaning: on-site vs off-site service compared.
Thermal cleaning on the bench versus regeneration in place
Both processes use heat to burn soot, and people sometimes assume they are interchangeable. They are not.
| Regeneration in place | Thermal cleaning on a bench | |
|---|---|---|
| Where | In the device, on the DG set | In an oven or burner station at a workshop |
| Heat source | Exhaust heat, plus a heater or fuel-assisted system in some designs | Oven or purpose-built heating equipment |
| Gas flow | The engine’s exhaust flow, which varies with load | Controlled airflow set by the operator |
| Control | The RECD controller and the engine’s load | A defined profile with element temperature measurement |
| Typical aim | Keep soot loading in check during service | Burn off residual soot and loosen deposits during a cleaning |
| Ash | Not removed | Not removed; a later stage is needed |
| Record | Controller cycle log | Profile sheet and temperature trace |
The practical consequence is that a failed regeneration does not become a successful one by sending the element to an oven, and an oven bake does not substitute for the supplier’s regeneration design. If the element’s problem is a weak heater or a narrow passive window, a bake treats nothing. Our article on RECD regeneration vs filter cleaning: which service is needed shows how to tell which situation you are in before you spend money on either.
Safety and environment at the provider’s premises
Thermal cleaning concentrates fire, smoke and heat in one place. Before you send an element, it is reasonable to ask about the workshop itself.
- Fire safety. Is the oven area separated from combustible materials, and are there extinguishing arrangements suited to the equipment?
- Fuel and oil handling. How are oily or fuel-soaked elements stored before they go in, and are they kept away from ignition sources?
- Operator training. Who monitors the cycle, and are they trained to respond to a temperature alarm or smoke?
- Emissions. Does the oven exhaust pass through treatment, and does the workshop operate within its consent conditions?
- Waste. What happens to the ash, the collected dust and any condensate, and will you receive a record? See handling soot and ash removed during RECD servicing.
- Insurance and liability. Is your element covered while in the provider’s custody, and who bears the loss if it is damaged?
None of these questions is hostile. A provider with a well-run workshop will have the answers to hand and may be glad to be asked, because their competitors often are not. An unwillingness to describe the arrangements is itself information.
Mistakes to avoid
- Assuming a bake is a full cleaning. It is half of one.
- Accepting “overnight” as a profile.
- Skipping the screening of oily or damaged elements.
- Ignoring where temperature is measured.
- Sending the same element for thermal cleaning again and again without tracking the cycle count.
- Confusing thermal cleaning with on-engine regeneration. Both use heat, but regeneration happens in place with the engine’s gas flow and its controls, while a bench bake is a separate controlled process.
- Believing that more heat means a cleaner element.
FAQ
Does thermal cleaning remove ash?
No. It oxidises soot and loosens carbon-bound deposits, but ash is incombustible and stays in the element. A second stage, such as controlled air or wet cleaning, is needed to remove it.
Can thermal cleaning damage a catalyst coating?
Yes, if the temperature or duration exceeds what the coating tolerates. Ask for the supplier’s approved range and for the logged temperature trace from your element’s cycle.
How hot does the element get?
The peak temperature depends on the element, the coating and the approved profile, and the element’s own temperature can differ from the oven setpoint, particularly while soot burns. Ask where the temperature is measured and for the recorded trace.
How long does thermal cleaning take?
Reported figures for truck filters range from several hours to around a day including cool-down. For your element, ask for the approved profile and the provider’s turnaround commitment in days, including transport and the second stage.
Is on-site thermal cleaning possible?
Some equipment is built to heat an element under controlled conditions, but the questions above apply with greater force, particularly on off-gas, fire safety and temperature records. A plant room with an open flame or an improvised heater is not a suitable place.
Can I just run a long regeneration instead?
Sometimes, for soot. A supervised regeneration or loaded run can burn soot in place if the design supports it, but it does not remove ash and is not a substitute for cleaning an ash-loaded element. See how to tell whether an RECD filter is ash-loaded.
Bringing it together
Thermal cleaning is a legitimate and often essential stage, but it is only as good as its control. Ask whether the process is approved for your element, how it screens oily or damaged elements, what the temperature profile is and where it is measured, how soot burn-off and off-gas are handled and what follows the bake to remove the ash and prove the result. Use the profile sheet to see the answers on paper, and score the provider on the fourteen questions before you decide.
If you would like help judging a thermal cleaning quotation, browse our retrofit emission control devices, read our FAQ or contact the Aceget team with your element details and the provider’s proposal.
Related Reading
- Soot vs Ash in RECD Regeneration
- Can You Wash an RECD Filter? Questions to Ask Before Cleaning
- Why Compressed-Air Cleaning May Be Unsuitable for Some RECD Filters
- Catalysed vs Uncatalysed RECD Filters
- RECD Regeneration vs Filter Cleaning: Which Service Is Needed?
- RECD Cleaning Report: How to Verify That the Service Was Effective