- November 15, 2026
- Posted by: editor
- Category: RECD & Emission Control Devices
“We’ll just blow it out with compressed air.” It is the most common sentence in filter cleaning, and it is not wrong. Air is a genuine cleaning method, widely used by workshops and recognised in regulatory guidance. The US Environmental Protection Agency, in a guidance document on diesel particulate filter maintenance, describes cleaning in general as heating the filter and using compressed air combined with a vacuum system so that ash is blown from the filter and captured in a sealed container (EPA 420-F-10-027).
Notice the details in that sentence: heating, a vacuum and a sealed container. Air is a stage in a controlled process, not a single act performed with a nozzle. When “blow it out” means exactly that, with no enclosure, no extraction, no flow test and no regard for the element’s condition, compressed-air cleaning of an RECD filter can be ineffective, unsafe or damaging.
This article explains when air works, when it does not and how to tell the difference. We examine eight ways air cleaning goes wrong, give you a suitability screen to apply to your own element, show how a flow-test plateau reveals an incomplete clean and offer questions to put to any provider who proposes air as the method. Where a point depends on your device, ask the supplier. The goal is to help you decide, not to condemn a useful technique.
What compressed air can do well
Be fair to the method first. Air is useful because it is dry, quick and does not introduce water or chemicals into a ceramic that may be sensitive to both. It is effective on loose, dry ash that has settled in the channels, especially in the early part of the cleaning. A 2006 SAE study using flow benches on heavy-duty filters found that the first ten minutes of air cleaning removed more than 55% of the filter’s soot and ash (SAE 2006-01-3256). A trade article quoting a cleaning operator says air typically gets a filter about 75% clean, with wet cleaning needed for the rest (Fleet Maintenance). Those are workshop figures for vehicle filters, not a promise for your element, but they illustrate the pattern: air does a lot quickly and then stops helping.
That pattern is the key to the whole subject. Air is excellent at the easy part and limited at the hard part.
Eight ways air cleaning goes wrong
Failure mode 1: The direction is wrong
A wall-flow filter has channels plugged at alternating ends. Gas enters the open inlet channels, passes through the porous walls and leaves by the neighbouring channels. Ash collects against the plugs at the rear of the inlet channels. To push it out, air has to travel from the clean side back toward the dirty side, so that ash leaves the way it came in. One engine dealer’s maintenance note describes blowing air from the outlet end toward the inlet end into a vacuum fitted with a HEPA filter (Foley Engines). Blow the other way and you pack ash harder against the plugs.
How it shows up. Pressure drop is unchanged or worse after “cleaning”.
Failure mode 2: The cleaning is uneven
Air nozzles treat a small area at a time. A technician waving a nozzle across the face cannot guarantee that every channel receives the same treatment. A trade article quoting an industry executive observes that pulse cleaning assumes all cells are plugged equally, which gives inconsistent and incomplete results, and that cells near the outer edge tend to collect more ash than those near the centre (Overdrive). Scanning systems that treat both ends of the element in a regular pattern exist precisely to address this, but a handheld gun does not.
How it shows up. The centre is clear and the rim is not. Pressure drop improves somewhat but never reaches the reference.
Failure mode 3: The deposit is not loose ash
Air moves loose particles. It does not dislodge deposits that are sticky, oily, glazed or fused. Wet stacking leaves an oily soot layer that clings to the walls; our article on RECD regeneration after wet stacking describes how it arises. High-temperature events can sinter ash into harder masses. The cleaning industry’s usual answer is a thermal step first, to turn gummy residue into a powder that air can then remove. An Overdrive trade article describes baking a filter for 4 to 24 hours, depending on design, to loosen carbon, much as a self-cleaning oven turns baked-on grime into powder. A pure air job on such a filter is aimed at the wrong target.
How it shows up. The first minutes of cleaning achieve a lot, and then nothing more comes out.
Failure mode 4: Pressure and nozzle distance are not controlled
Ceramic walls are thin. Too much pressure, or a nozzle held too close, can crack walls or erode the face. Procedures that exist for specific filters specify pressures and distances. The dealer note mentioned above, for one family of filters, specifies air at around 80 psi, a nozzle held at least two inches from the surface and a duration of about ten minutes. Those numbers belong to that filter and that procedure. The point is not to copy them but to notice that someone had to decide them, and that a provider without such parameters is improvising on a fragile part. Elements that have been through many thermal cycles, or through an overheated event, may be weaker than they look.
How it shows up. Sometimes it does not, until a crack lets particulate bypass the filter. A bypass can even lower the pressure reading, which looks like success.
Failure mode 5: Air cleans flow, not catalyst
Cleaning with air can restore flow without restoring catalyst activity. If the coating is masked by an oily film or has aged, regeneration behaviour will still be poor after a good air clean. Owners sometimes conclude that the cleaning “did not work” when the pressure came down but regeneration problems remained. See catalyst poisoning in an RECD and catalyst ageing and RECD regeneration behaviour.
How it shows up. Pressure improves, but regeneration is still slow or passive regeneration still does not work.
Failure mode 6: Containment fails
Blowing air through a filter creates a cloud of fine particulate. California’s air regulator, in a guide to ash handling from diesel filters, states that blowing compressed air through a filter in an uncontrolled way would release ash into the air and recommends that, if used at all, the air be blown into a chamber with a HEPA filter that collects the particulates for proper disposal (CARB ash guide). That guide also notes the ash may be classed as hazardous waste in some circumstances. The rules in India are set by your State Pollution Control Board and the applicable waste regulations, so confirm what applies to you. As our article on handling soot and ash removed during RECD servicing says, compressed air belongs only inside an enclosed, extracted cabinet, never in an open plant room, car park or rooftop.
How it shows up. Dust on surfaces, in the plant room and in the air intake, complaints from staff and a waste stream nobody planned for.
Failure mode 7: The air supply is dirty
A compressor line can carry oil mist and moisture. Blowing contaminated air through a clean ceramic leaves oil or water in the pores, which is the opposite of what is wanted. A workshop that uses air should have filters, dryers and drains on its compressed-air supply and should be able to tell you so.
How it shows up. An element that is lighter but wetter or oilier than expected, and pressure that does not recover as predicted.
Failure mode 8: Nothing proves it worked
The most serious failure is the absence of a test. Air cleaning makes the inlet face look clean quickly, because the visible ash on the surface goes first. Without a flow or pressure-drop measurement and a weight record, “clean” is an impression. A trade article quoting a truck-parts manufacturer said testing after cleaning is the most critical part of the process, because without it nobody knows whether the filter is ready to go back into service (FleetOwner).
How it shows up. It does not show up until the pressure creeps back after refit.
A worked plateau: when air stops helping
The following is an illustrative flow-bench record, not a real job. A provider cleans an RECD element with a controlled air process in an enclosed cabinet, testing after each pass. The test measures pressure drop at a standard airflow. The reference value for a clean element of this type is 40 mbar. The acceptance criterion agreed with the supplier is within 15% of the reference, so 46 mbar or below.
| Stage | Pressure drop at test flow (mbar) | Restoration of the excess |
|---|---|---|
| As received | 110 | 0% |
| After pass 1 | 68 | (110 − 68) ÷ (110 − 40) = 42 ÷ 70 = 60% |
| After pass 2 | 59 | 51 ÷ 70 = 73% |
| After pass 3 | 58 | 52 ÷ 70 = 74% |
| Acceptance limit | 46 | n/a |
Reading the record. Pass 1 removed most of what air can move. Pass 2 gave a modest further gain. Pass 3 gave almost nothing. The pressure drop has plateaued at 58 mbar, which is above the acceptance limit of 46. The remaining restriction is therefore not loose ash. It might be oily or hardened deposit, ash packed against the plugs, or something else. The correct response is to move to another stage, such as a thermal or wet step if the supplier approves them, not to keep blowing. If the provider had stopped after pass 1 and shown the customer a clean-looking face, the element would have gone back with a pressure drop 70% above the reference, since (68 − 40) ÷ 40 = 70%. Even after pass 3 it sits 45% above, since (58 − 40) ÷ 40 = 45%, so the plateau itself is the evidence that another stage is needed.
This is why every credible cleaning process pairs a cleaning stage with a test. It is also why “air only” is a statement about the method, not about the outcome.
The suitability screen
Use the screen below to judge whether air alone is plausible for your element. Answer each row from your records and inspection, then read the pattern.
| Question | Favours air | Against air alone |
|---|---|---|
| What is the deposit? | Dry, loose, pale ash | Oily, sticky, glossy or fused |
| What is the element’s condition? | Intact, no cracks or glazing, known history | Cracks, hot spots, unknown or heavy history |
| Is it catalysed? | No, or the supplier confirms the method is fine | Yes, and performance (not only flow) matters |
| How is it constructed? | Solid, documented tolerances | Segmented or cemented, or a design the supplier restricts |
| What equipment is proposed? | Enclosed cabinet, extraction, HEPA, regulated pressure, consistent scanning | Handheld gun, open area |
| What is the air quality? | Filtered, dried | Unknown compressor, drains not maintained |
| Is a test bench available? | Yes, with before/after records | No |
| Does the supplier approve air for this model? | Yes, in writing | Silent or negative |
Rules of thumb. If every row favours air, air as a first stage is reasonable, and a plateau test will show whether it is enough. If one or two rows are against air alone, ask for a combined method. If the deposit is oily or fused, the element’s condition is doubtful, or the supplier does not approve it, treat air alone as unsuitable.
Two examples
Element A. A standby set’s cartridge, intact, with a documented history, carrying dry grey ash. The provider has an extracted enclosure and a flow bench. Supplier approves air in the O&M manual. Verdict: air as the first stage is suitable. Check for the plateau and the acceptance limit.
Element B. A prime-power set’s element that ran a long period with blue smoke at start-up, with glossy dark patches on the inlet face and an unknown cleaning history. The provider proposes “a good blow-out on site”. Verdict: unsuitable on its own. Ask for a combined approach and a test, and consider an inspection by the supplier first.
What good air cleaning looks like
When air is appropriate, the process has recognisable features.
- An enclosed cabinet with a sealed door and a defined extraction path ending in a HEPA stage.
- A consistent pattern, such as automated scanning of the whole face, not a handheld wave.
- Regulated pressure and distance set by procedure, with the nozzle never in contact with the element.
- Bidirectional treatment where the method calls for it, so both faces are addressed.
- Dry, filtered air, with a maintained compressed-air supply.
- Weighing and flow testing before and after, with the readings recorded.
- A defined stopping rule, such as “repeat until the reading is within X of the reference or until two passes give no further gain, then escalate”.
- A record of the method, operator, date, readings and waste handling.
Compare that list with a technician, a hose and a compressor in the corner of a plant room.
How air fits into a combined process
In practice, air is often combined with other stages. A 2023 SAE paper tested three families of cleaning methods, namely thermal and pneumatic, ultrasonic and aqueous, using a non-destructive method to quantify the soot and ash left in the filters. It found at least satisfactory ratings for all systems evaluated and very good ratings for two, with up to 96% of deposits removed by one system (SAE 2023-01-0376). The lesson for owners is twofold. First, a well-run process of almost any family can perform well, so the method name is not the guarantee. Second, there are measurable differences between systems, so what matters is the measurement. For questions about thermal stages, see thermal cleaning of RECD filters: what owners should ask the provider. For wet methods, see can you wash an RECD filter?. For claims about ultrasonic processes, see ultrasonic RECD cleaning claims: what evidence should buyers request?.
Questions to ask a provider who says “we use compressed air”
- Is the cleaning done inside an enclosed, extracted cabinet? Where does the extracted air go, and is there a HEPA stage?
- Is the air pressure regulated, and what pressure and nozzle distance do you use? Where do those values come from?
- Do you treat both ends of the element, and in what direction?
- How is the compressed air filtered and dried?
- What do you do if loose ash is removed but pressure is still high? What is the next stage?
- Do you weigh and flow-test the element before and after? What is the pass criterion, and who set it?
- Has the supplier approved this method for my element? Can I see it in writing?
- How do you handle and dispose of the collected ash, and what record do I receive?
A provider that has ready answers is probably running a real process. One that cannot answer, or says “we’ve always done it this way”, is telling you something useful. If you need to rank providers on these answers, the weighted matrix in RECD filter cleaning: on-site vs off-site service compared can take them as criteria.
After an air-only clean: what to watch
If you accept an air-only service for a suitable element, protect yourself afterwards.
- Take the “before” readings at the reference load, including pressure, load and run hours.
- Keep the weight and flow records the provider gives you.
- Read pressure at the reference load for the next several runs. A rapid rise suggests the clean was incomplete or that oily soot is still being produced.
- Check regeneration behaviour. If cycles still struggle, the problem may be the catalyst or the heater, not ash.
- Compare with the plan. If pressure at the reference load is still more than a modest margin above baseline, follow the troubleshooting in why RECD pressure can stay high after a cleaning service.
Mistakes to avoid
- Doing the job in the plant room because the compressor is there.
- Judging success by the look of the inlet face.
- Repeating air passes indefinitely after the plateau.
- Using air on an element with cracks or glazing without the supplier’s approval.
- Ignoring the waste. Collected ash is a waste stream with its own handling rules.
- Assuming “air only” is cheaper in total. A repeat cleaning costs more than a proper one.
FAQ
Can you clean a DPF or RECD filter with compressed air?
Sometimes, and often as one stage of a controlled process. It works best on loose, dry ash in an intact element, using an enclosed, extracted cabinet, regulated pressure and testing. It is poorly suited to oily, glazed or fused deposits and to elements of doubtful condition.
Does compressed air damage a ceramic filter?
It can if the pressure is too high, the nozzle is too close or the element is already weakened. Procedures for specific filters define safe parameters, so follow the supplier’s. A cracked element can pass particulate unfiltered, which makes the damage hard to see.
Why is my filter still blocked after air cleaning?
The remaining restriction may be oily or hardened deposit, ash compacted against the plugs, an uneven clean or a problem that is not the filter at all, such as a sensor or exhaust restriction. A flow-test record helps identify which.
Is it acceptable to use a leaf blower or workshop compressor on site?
Not in an open area. Blowing out an element outside a containment cabinet spreads fine particulate and may breach waste and workplace rules. Use a HEPA vacuum and damp wiping for surface cleaning on site, and send the element for proper cleaning if the channels need clearing.
What pressure should be used?
There is no universal figure. It depends on the substrate, construction, nozzle and procedure. Ask the supplier for the approved procedure for your element. Treat any provider that cannot name its parameters with caution.
Is vacuum-only cleaning enough?
For loose surface deposits, a HEPA vacuum is appropriate and safe. It does not clear ash from deep in the channels, so it should not be sold as a full cleaning.
Bringing it together
Compressed air is a respectable cleaning tool and a poor stand-alone strategy for many RECD elements. It excels at loose, dry ash and fails at oily, fused or uneven deposits, at protecting people from dust and at proving what it achieved. Treat “we’ll blow it out” as the start of a conversation. Ask about the enclosure, the pressure, the pattern, the air quality, the next stage and the test, and use the suitability screen before you agree.
If you would like help deciding what method suits your element, browse our retrofit emission control devices, read our DG set emission regulations overview or contact the Aceget team.
Related Reading
- Handling Soot and Ash Removed During RECD Servicing
- Can You Wash an RECD Filter? Questions to Ask Before Cleaning
- Thermal Cleaning of RECD Filters: What Owners Should Ask the Provider
- RECD Filter Cleaning: On-Site vs Off-Site Service Compared
- Refurbished RECD Filter Core Reuse
- Why RECD Pressure Can Stay High After a Cleaning Service
[…] in an extracted cabinet or a wet process, and whether each stage is approved for the element. See why compressed-air cleaning may be unsuitable for some RECD filters and can you wash an RECD […]