- October 29, 2026
- Posted by: editor
- Category: RECD & Emission Control Devices
An RECD-equipped DG set usually has two service relationships. The engine dealer or AMC contractor looks after everything up to the exhaust manifold and turbocharger outlet. The RECD supplier, or a service company it has trained, looks after the device on the exhaust line. Each team knows its own equipment well. Very few sites have a written plan for the moments when their work overlaps, and DG engine repairs and RECD care overlap more than most people expect.
The reason is simple geometry. The RECD sits downstream of every engine mistake. Oil past a stem seal, coolant from a weeping head gasket, fuel from a dribbling injector or debris from a failed turbo all end up in the exhaust device. The engine can be repaired in a day; a filter element loaded with oil ash or cracked by a thermal event is a longer and costlier conversation.
This guide is for the maintenance manager or plant engineer who must hold both teams together: failure paths, a repair-type matrix, a RACI, an overhaul timeline, emergencies, running-in and who pays.
How engine faults reach the RECD
The table lists common engine faults, what each sends down the exhaust, and the typical effect on an RECD. Wall-flow filters, partial-flow filters, catalyst-coated substrates and electrostatic or wet-type units respond differently, so treat this as a guide to questions, not a diagnosis.
| Engine fault | What reaches the exhaust | Likely effect on the RECD |
|---|---|---|
| High lube oil consumption (worn rings, liners, valve guides, stem seals) | Unburnt and partly burnt oil, oil additive ash | Ash build-up that does not burn off, glazed or varnished surfaces, steadily rising back-pressure, possible catalyst masking |
| Coolant leak into cylinders (head gasket, cracked head, liner seal, oil cooler) | Steam, glycol, coolant additive residue | White crusty deposits, wet loading of the filter, risk of thermal shock cracking on ceramic media |
| Injector dribble, poor spray pattern, overfuelling, wrong timing | Heavy soot, raw fuel droplets, hydrocarbons | Rapid soot overload; on filter designs, risk of an uncontrolled soot burn and local overheating |
| Turbocharger failure (seal, bearing, wheel contact) | Large volumes of oil, metal fragments, sometimes pieces of wheel | Oil soaking of the device, physical damage to inlet face, blocked channels, sudden back-pressure jump |
| Prolonged low-load running | Wet soot, unburnt fuel and oil (wet stacking) | Sticky deposits that resist cleaning, more frequent cleaning intervals |
Most of these faults show up first as smoke. Our guides to blue smoke from a generator, black smoke and its usual causes and white smoke and coolant or fuel problems explain the engine side. With an RECD fitted, visible smoke may be reduced, so the device can hide the symptom while absorbing the damage. Back-pressure trends and oil top-up records therefore matter more on an RECD-equipped set.
Oil consumption deserves special attention. Lubricant additives leave incombustible ash, and on filter-type RECDs that ash stays until it is cleaned out mechanically. DieselNet’s overview of ash in diesel particulate filters explains why ash behaves so differently from soot. If you are unsure whether your engine’s oil burn is acceptable for the device, our article on engine oil consumption and RECD suitability sets out the questions to ask.
Repair-type matrix: when to involve the RECD team
Not every engine job needs the RECD engineer on site. A fuel filter change does not; a turbocharger replacement certainly does. Use the matrix below as a starting point, agree your own version with both providers and attach it to both contracts.
| Engine repair | Involve RECD team? | What to protect | Post-repair checks on the RECD |
|---|---|---|---|
| Routine oil, fuel and air filter change | No, inform only | Nothing specific | Note hours and oil grade in the shared log |
| Injector replacement or calibration | Yes, after | Record pre-repair ΔP and exhaust temperature | Compare ΔP at matched load; inspect inlet face if soot loading was high; clean if supplier advises |
| Fuel pump or timing adjustment | Yes, after | Record pre-repair baseline | Watch soot loading rate over the next 25–50 hours |
| Turbocharger replacement (planned) | Yes, before and after | Blank or cover the exhaust opening while the turbo is off | Inspect for oil and debris; check flange gaskets and clamps; new baseline |
| Turbocharger failure (unplanned) | Yes, immediately | Do not restart until the RECD is inspected | Full inspection, likely cleaning, possible element assessment |
| Head gasket or cylinder head work | Yes, before and after | Cover exhaust openings; prevent coolant draining into exhaust | Look for white deposits and moisture; check for cracks; new baseline |
| Valve stem seals, guides, rings or liners | Yes, before and after | Cover exhaust openings | Oil ash check; agree a running-in monitoring plan |
| Major (in-frame or out-of-frame) overhaul | Yes, at planning stage | Decide whether to remove or isolate the RECD physically while the set is out of service | Inspection and cleaning before recommissioning; new baseline after running-in |
| Exhaust manifold, bellows or pipe repair upstream of RECD | Yes, before | Alignment, support, gasket specification | Leak check, support check, update drawings |
Where repairs touch exhaust pipework, supports or the device’s position, follow the approach in our sibling post on updating RECD drawings and records after exhaust modifications so that your general arrangement drawing still matches what is on site.
A RACI for a typical engine repair
RACI stands for Responsible (does the work), Accountable (owns the outcome and signs off), Consulted (gives input before or during) and Informed (told after). The table below assumes five parties: the site owner or maintenance manager, the engine service company, the RECD service team, EHS, and the DG operator. Adapt the names to your organisation, but keep one A per row.
| Step | Owner / maintenance manager | Engine service company | RECD service team | EHS | DG operator |
|---|---|---|---|---|---|
| 1. Plan scope and downtime | A | R | C | C | I |
| 2. Isolate and lock out the set | A | R | I | C | R |
| 3. Protect or physically remove the RECD (set out of service) | A | C | R | C | I |
| 4. Carry out the engine repair | A | R | I | I | I |
| 5. First run after repair | A | R | C | I | R |
| 6. Inspect and clean the RECD | A | C | R | C | I |
| 7. Record a new back-pressure baseline | A | C | R | I | R |
| 8. Update records and logs | A/R | R | R | I | I |
| 9. Close-out and return to service | A | C | C | C | I |
Isolation and lockout
Both teams may work on the same machine on the same day. Use one lockout/tagout procedure with a personal lock for each person, covering battery, fuel and the auto-start signal from the changeover panel. The US OSHA page on control of hazardous energy is a useful reference for the principles; follow your own site’s permit-to-work system for the detail. Remember that exhaust components stay hot for a long time after shutdown, and an RECD with substantial thermal mass may be hotter than the engine block.
Protecting the RECD versus bypassing it
Bypassing the RECD so that the set can run without it is a compliance risk and not an acceptable shortcut, during repairs or at any other time. Running without it can expose the owner to sealing and penalties. Our article on what happens when a DG set is sealed for non-compliance shows how disruptive that can be.
Physically removing or isolating the RECD while the set is out of service for an engine repair is a different matter. The RECD team may unbolt the device, cap both ends and store it, or blank the inlet so dirt, washing fluid, coolant or dropped fasteners cannot enter. That is protection, not bypassing, on one condition: the set must not run until the RECD is refitted, inspected and signed off. Make that explicit:
- Tag the DG controller and the changeover panel with “RECD removed, do not run”.
- Disable auto-start until the RECD team signs the return-to-service note.
- Record the date and time of removal and refitting in the log.
- If an engine test run is truly needed before refitting, agree in writing with the RECD supplier and your consent conditions how it will be done; do not assume it is permitted.
First run and new baseline
The engine team owns the first run to confirm the repair; the RECD team needs data from that same run. Agree in advance what to record: load in kW, exhaust temperature before the RECD, differential pressure across it, and any controller alarms if your device has one. Our explainer on how exhaust back-pressure affects a DG set explains why both teams care about the same number from different directions.
Sequencing a planned overhaul: Day −14 to Day +30
A planned overhaul is the best case because there is time to coordinate. Shift the days below to suit your downtime window.
| Day | Activity | Lead |
|---|---|---|
| −14 | Confirm overhaul scope with engine service company; share scope with RECD team | Maintenance manager |
| −14 | Pull last 90 days of ΔP, exhaust temperature, oil top-up and run-hour data | Operator / maintenance |
| −10 | Joint meeting or call: agree whether RECD will be removed, blanked or left in place | Both teams |
| −10 | Agree consumables: gaskets, clamps, insulation, any RECD parts likely to be needed | RECD team |
| −7 | Book lifting equipment and confirm access route if RECD removal is planned | Maintenance manager |
| −3 | Record final pre-overhaul baseline at a known load (for example, 70%) | Operator, witnessed by RECD team |
| −1 | Issue permit-to-work, LOTO plan, waste handling plan | EHS |
| 0 | Isolate set; RECD team removes or blanks the device; engine team begins | Both teams |
| 0 to +5 | Engine overhaul; RECD inspected and cleaned off-site or on-site if planned | Engine team / RECD team |
| +5 | RECD refitted, joints and supports checked; return-to-service tag issued | RECD team |
| +5 | First run at light and stepped load; record ΔP and temperature | Engine team, RECD team consulted |
| +6 to +20 | Running-in period with enhanced monitoring | Operator |
| +20 | Interim review of oil consumption and ΔP trend | Both teams |
| +30 | Post-running-in baseline recorded; records closed out | Maintenance manager |
If this is an older set where an overhaul is overdue and the RECD has not yet been bought, the order of work is different. That situation is covered in our post on whether to complete an engine overhaul before fitting an RECD.
What to agree at the Day −10 meeting
Most coordination problems are prevented here. Settle: whether the RECD is removed, blanked or left connected; who supplies gaskets for broken joints; whether and where the RECD is cleaned; how residues are stored and disposed of; who records the post-repair baseline and at what load; and who signs the return-to-service note.
Waste handling often falls between two contracts. Our sibling guide on handling soot and ash removed during RECD servicing covers storage, labelling and how to confirm the right disposal route with your SPCB and an authorised recycler.
Emergency repairs: when the engine fails suddenly
The hard case is a turbocharger that fails at 2 a.m. during a grid outage. The temptation is to fit a replacement turbo and restart immediately. On an RECD-equipped set, that can turn one failure into two.
The rule: inspect the RECD before the next run
A failed turbo sends its bearing oil straight into the exhaust, often with fragments of wheel or housing. Restarting without checking can:
- Ignite oil soaked into a filter element and cause a local overheat.
- Drive metal fragments deeper into channels or against fragile surfaces.
- Push oily residue further into the device, making cleaning harder.
- Trip a high back-pressure condition that stresses the new turbo.
Your emergency procedure should state plainly that after a turbo failure, major coolant leak, runaway or sustained heavy smoke, the RECD is inspected before the next run.
An emergency checklist for the shift in charge
- Shut down the set and isolate auto-start.
- Note the time, load, any alarms, and what was seen or heard.
- Photograph the stack and any visible oil or smoke residue.
- Call the engine service company and the RECD service team at the same time, not one after the other.
- Do not open hot exhaust components; allow cooling and follow LOTO.
- Keep failed parts, including the turbo, for inspection. Do not let them be taken away unrecorded.
- Wait for the RECD team’s go-ahead before restart.
Check whether your RECD service response terms cover call-outs triggered by engine events. If you use an independent service company for the device, our batch post on using a third-party service company to maintain an RECD explains how to define that interface.
Running-in after an overhaul
A freshly overhauled engine often consumes more oil while new rings and liners bed in. The OEM running-in procedure exists for the engine, but it matters just as much to the RECD, because the extra oil goes into the device.
Discuss running-in with both parties
Get the OEM running-in instructions in writing, including expected oil consumption, and ask the RECD supplier:
- Is the expected running-in oil consumption acceptable for this device, and for how long?
- Should the device be cleaned or inspected at the end of running-in?
- Are there load patterns during running-in that the device does not tolerate well, such as long periods at very low load?
Low-load running is a frequent conflict: staged engine loading versus RECD designs that need exhaust temperature to manage soot. If your device relies on passive regeneration, DieselNet’s page on DPF regeneration explains why temperature and load matter. Agree a load plan that satisfies both, using a load bank if necessary.
A simple running-in monitoring plan
| Parameter | Frequency during running-in | Who records | Action trigger |
|---|---|---|---|
| Oil top-up volume and engine hours | Every run, or daily | Operator | Consumption above OEM running-in guidance |
| ΔP across RECD at a fixed reference load | Every 10 run hours | Operator | Rise faster than the pre-repair trend |
| Exhaust temperature before RECD | Every 10 run hours | Operator | Outside the device’s stated range |
| Visible smoke at stack | Every run | Operator | Any blue or white smoke |
| Controller alarms, if fitted | Every run | Operator | Any new alarm type |
At the end of running-in, record the new baseline. This is the reference that future trends and service reports will be judged against.
Engine repair and the RECD back-pressure baseline
The back-pressure baseline is the most useful number linking engine health and RECD health. Re-record it after almost any engine repair: the repair may have changed exhaust flow or temperature, and the RECD may have been cleaned, resetting its loading.
When recording a baseline, keep the conditions fixed: the same load, after the same warm-up time, with the same fuel. Our guide to how fuel and engine condition confound RECD tests explains why a baseline taken on a sick engine, or on a different fuel batch, can mislead you for months.
Record it on a dated sheet signed by the operator and the RECD engineer, and attach it to the service report. If service reports at your site tend to be thin, our sibling post on auditing an RECD service report for missing information lists the fields that should never be blank, including baseline load and ΔP.
Illustrative example: injector fault on a 400 kVA set
The following example is illustrative. The numbers are chosen to show the method and are not data from any specific site or device.
A commercial building operates a 400 kVA DG set fitted with an RECD. After commissioning, the team recorded a reference ΔP of 4.2 kPa at 70% load. Over the following months, ΔP at that load stayed close to 4.2 kPa between scheduled cleanings.
Then the operator noticed the reading creeping up. Over 60 run hours, ΔP at 70% load rose from 4.2 kPa to 7.1 kPa. At the same time, the stack showed occasional dark puffs on load acceptance.
Step 1: Size of the rise
- Rise = 7.1 − 4.2 = 2.9 kPa
- Percentage rise = 2.9 ÷ 4.2 × 100 = 69.0% (to one decimal place)
Step 2: Rate of rise
- 60 run hours = 6 blocks of 10 hours
- Rate = 2.9 ÷ 6 = 0.48 kPa per 10 run hours (0.4833, rounded)
That rate was several times the post-commissioning trend, pointing to an engine-side cause. The maintenance manager called both teams. The engine service company found one injector with a poor spray pattern and dribble. The RECD team confirmed heavy soot loading but no visible damage to the inlet face.
Step 3: After repair and cleaning
The injector was replaced, the RECD was cleaned as per the supplier’s procedure, and a new baseline was recorded at 70% load after the agreed warm-up:
- New baseline = 4.4 kPa
- Difference from original = 4.4 − 4.2 = 0.2 kPa
- As a percentage of original = 0.2 ÷ 4.2 × 100 = 4.8% (to one decimal place)
A small residual rise can come from ash that cleaning does not fully remove, measurement tolerance or ambient differences. What matters is that future trends are now measured from the documented 4.4 kPa, not 4.2 kPa.
Neither team would have solved this alone. Without a shared ΔP trend, the RECD might simply have been cleaned more often while the injector kept overloading it.
The site also logged the cost of the extra cleaning and the injector work against run hours. Our sibling post on tracking RECD service costs per operating hour shows how incidents like this distort cost-per-hour figures, and why it helps to tag engine-caused RECD costs separately.
Who pays when engine faults damage the RECD?
If a turbo failure soaks the RECD in oil, or an injector fault overheats a filter element, three parties may be involved: the owner, the engine service provider and the RECD supplier.
Read the RECD warranty first
Most RECD warranties cover defects in materials and workmanship within stated operating conditions. Damage caused by abnormal engine behaviour, such as excessive oil consumption, coolant ingress or overfuelling, is commonly listed as an exclusion. Read your own terms carefully; our explainer on RECD warranty terms, parts, labour and exclusions shows what to look for. Never assume coverage either way.
Look at the engine service contract
If the fault arose from poor workmanship, such as a turbo fitted without proper oil priming, the engine service contract may apply. Many AMC contracts limit consequential liability, so check what yours says about connected equipment.
Build the evidence file
Whoever pays, the decision will rest on evidence. Keep:
- ΔP and temperature logs for the weeks before the event.
- Oil top-up records and run hours.
- Photographs of the failed engine part and of the RECD inlet face before cleaning.
- The engine service company’s job card, with root cause.
- The RECD team’s inspection report.
Our batch post on what to record when raising an RECD warranty claim gives a detailed evidence list.
Records to update after every engine repair
Close-out is where repairs quietly fail: the engine runs and the paperwork waits. Within a week of any repair in the matrix, complete:
- Engine job card filed with root cause and parts replaced.
- RECD inspection and cleaning report with before and after condition.
- New ΔP baseline sheet, signed and dated.
- Shift log entry noting the repair and the new baseline.
- Any change to exhaust layout reflected on the drawings.
- Waste manifest or disposal record for soot, ash and oily residue.
- Cost entries tagged as engine-caused or routine.
These records show an SPCB inspector that the device was looked after through the engine work. Requirements vary by state and consent condition, so confirm with your SPCB. The Central Pollution Control Board website is the starting point for national guidance on DG set emissions and RECD testing.
FAQ
Do I need the RECD service team for every engine repair?
No. Routine filter and oil services only need a log entry. Involve the RECD team for fuel system, turbo, cylinder head, ring or liner work, overhauls and upstream exhaust work.
Can the RECD be removed during an engine overhaul?
It can be physically removed or blanked while the set is out of service, if the RECD supplier agrees and does the work. The set must not run without it. Tag the controls, disable auto-start and only return the set to service after the device is refitted and signed off.
Can a turbocharger failure damage the RECD?
Yes. A failed turbo can send large amounts of oil and metal debris into the exhaust. Inspect the RECD before the next run, and keep the failed turbo for root-cause analysis.
Why does back-pressure need a new baseline after engine repairs?
The repair may change exhaust flow or temperature, and the RECD is often cleaned at the same time. A fresh baseline at a fixed load gives a correct reference for future trends.
Will higher oil consumption during running-in harm the RECD?
It can add ash and residue. Get the expected figure from the engine OEM, confirm tolerance with the RECD supplier, and monitor ΔP and oil top-ups until the engine settles.
Who pays if an engine fault damages the RECD?
It depends on the RECD warranty terms, the engine service contract and the evidence. Damage from abnormal engine operation is often excluded from RECD warranties, so keep logs, photographs and both teams’ reports.
Plan Engine Work Without Putting Your RECD at Risk
Aceget supplies CPCB type-approved retrofit emission control devices for DG sets from 25 kVA to 2500 kVA, and our team regularly works alongside engine dealers and AMC contractors on sites across India. If you have an overhaul, turbo replacement or recurring engine fault coming up, we can help you agree inspection points, cleaning needs and a new baseline before work starts. You can review our type approval certifications or contact our service team to plan the coordination.